Error Code P0961: What It Means & What To Do?

<<See All OBD Codes

The trouble code P0961 can be explained as Pressure Control Solenoid "A" Control Circuit Range/Performance. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another. If there is an appearance of the P0961 trouble code, then it would mean that the engine control module has discovered the levels of voltage to be outside the manufacturer’s parameters.

Do you want to know more about the P0961 fault code? Don’t worry! Parts Avatar Canada is here at your service. There can be a lot of situations where the automatic transmissions will include at least three pressure control solenoids which are known as solenoid A, B and C. The transmissions which are new would have more gears as well as more solenoids. There are a lot of error codes which are related to the "A" solenoid control circuit and some of the most common include P0960, P0961, P0962 and P0963. If the powertrain control module would detect an issue with the transmission pressure control solenoid "A" control circuit, then it would give rise to the P0961 error code. The particular code which is triggered depends upon the specific fault which the PCM has detected.

What causes this problem with the Pressure Control Solenoid "A" Control Circuit Range/Performance?

• Faulty transmission pump
• The transmission valve body might not be functioning properly
• Imperfect or damaged wiring
• There can be inoperative powertrain control module
• Malfunctioning pressure control solenoid
• There can be plugged hydraulic passages
• The transmission fluid might be contaminated
• Confined transmission filter
• Eroded or flawed connector

1. Engine Control Module - A faulty Engine Control Module can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Auto Transmission Control Module - If everything is alright with PCM, then there is surely some defect in Auto Transmission Control Module. Get it replaced before the situation gets worse.
3. Automatic Transmission Filter - P0961 code can display due to some faults in the Automatic Transmission Filter. So it is very important to replace the Automatic Transmission Filter with us at equitable prices.
4. Electronic Control Unit - Do you remember when was the last time you got your car Electronic Control Unit checked up? A dirty Electronic Control Unit can cause a lot of issues like displaying P0961 code.
5. Body Control Module Component - Poor Body Control Module Component can cause a lot of difficulties, so why not get it replaced at time?
6. Powertrain Control Module - Are there some faults in your Powertrain Control Module? Don’t waste time and get them replaced or else P0961 code can turn up.
7. Automatic Transmission Fluid - OBD Code P0961 can appear because of faulty Automatic Transmission Fluid.

There could be countless symptoms which that would accompany with this fault code. Willing to know some common symptoms of OBD Trouble Code P0961? Your wish is our demand. Have a look at them below:

Common Symptoms:

• There can be symptoms of misfire
• The PCM may put the transmission into limp mode
• Rising fuel consumption
• There can be an overheating transmission
• Transmission skid when carrying
• Check engine light might come into signal
• Transmission shifts forcefully

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Repair or replace the quirky engine control module
• Rehabilitate the defaults in the pressure control solenoid valve assembly
• You must clean the control solenoid valve
• Clear all the codes and then take the vehicle out for a test drive
• It is essential to restore the flawed wiring and connectors
• Carefully adjust the faults in the transmission control module assembly
• Recondition the non-functioning transmission control module

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of Transmission Oil, Manual Transmission Fluid, Honda Transmission Fluid, Pcm Car, Atf Fluid, Toyota Transmission Fluid, Atf Oil and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0961 code to be stored:

• The P0961 trouble code can be easily diagnosed by using an OBD scanner.
• You must visually inspect all wiring, connectors, and harnesses for signs of damage, flaws, or sometimes even wear.
• Carefully examine the transmission control module assembly.
• The overall temperature of the transmission fluid should be between 122-176-degrees-Fahrenheit.
• The automobile should be operated in second gear to ensure a 5-degree increase in transmission control module temperature, then you can run the automobile in park for five seconds.

Common Mistakes When Diagnosing The P0961 Code

• Transmission shift solenoid might start failing