P0960 - OBD Trouble Code

<<See All OBD Codes

The trouble code P0960 can be defined as Pressure Control Solenoid "A" Control Circuit/Open. This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code. It is a generic powertrain code which is associated to the transmission. It includes the defects in the pressure as well as some faults in the sensor. If the engine control module would receive a signal that the pressure control solenoid for the A control circuit is open, then the P0960 trouble code would start appearing.

It is always good to learn more! That is the reason we are here to help you out in gaining more knowledge about the P0960 error code. This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another. If the transmission control module would observe some issues with one of the valves, including a voltage signal stating that the A control circuit is remaining open, or not receiving the reference voltage needed to operate, then the P0960 fault code would be stored in.

What causes this problem with the Pressure Control Solenoid "A" Control Circuit/Open?

• Burned or quirky connector
• Faulty or damaged wiring
• Malfunctioning transmission pump
• There can be inoperative transmission valve body
• The hydraulic passages might be clogged
• Faulty pressure control solenoid
• There can be polluted transmission fluid
• Cramped transmission filter
• Imperfect PCM

1. Auto Transmission Control Module - Did your mechanic just found out that there is some fault in the Auto Transmission Control Module? Buy top notch Auto Transmission Control Module from us at economical prices.
2. Engine Control Module - A broken Engine Control Module can cause a lot of issues. It would be nice if you get it replaced on time.
3. Powertrain Control Module - Everything is fine with the Auto Transmission Control Module and still OBD code P0960 flashing? Then there is definitely some fault with the Powertrain Control Module. Get it checked and replace if needed.
4. Automatic Transmission Fluid - Automatic Transmission Fluid is an important car part which should never be neglected. May be there is some fault in it due to which P0960 code may start flashing.
5. Body Control Module Component - A faulty Body Control Module Component can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Electronic Control Unit - If everything is alright with PCM, then there is surely some defect in Electronic Control Unit. Get it replaced before the situation gets worse.
7. Automatic Transmission Filter - P0960 code can display due to some issues in the Automatic Transmission Filter. So it is very important to replace the Automatic Transmission Filter with us at equitable prices.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0960 code by mentioning some major symptoms below:

Common Symptoms

• Transmission slide when moving
• Some misfire like symptoms
• Growth in the fuel consumption
• The service engine soon light can start lighting up
• Transmission might move hardly
• Transmission might start overheating
• The transmission might be put into limp mode by the PCM

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0960:

• Rehabilitate the defaults in the transmission control module
• The pressure control solenoid should be restored to working order
• Make sure to mend the faulty wire harness from the transmission control module
• You must fill the transmission fluid as per the parameters of the manufacturer
• It is important to perform a full transmission flush
• Repair or replace the quirky pins
• The malfunctioning ECM should be repaired or replaced as per the need
• All the codes should be cleared up and then the vehicle should be taken out for a test drive

However, if you face any issue then we have stocked a wide range of best priced Transmission Oil, Manual Transmission Fluid, Honda Transmission Fluid, Pcm Car, Atf Fluid, Toyota Transmission Fluid, Atf Oil and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• The first thing which a mechanic should do is to use an OBD-II scanner so that he can inspect the stored P0960 trouble code.
• After that the transmission fluid levels as well as quality should be examined properly.
• Inspect the transmission pan for clutch or some other dirt or debris.
• A visual check of the wiring and related electrical circuitry and constituents should be performed which are associated with the pressure control solenoid A control circuit.
• Carefully scan the wire harness from the transmission control module to the transmission for defects.
• Check up the transmission control module and transmission connectors for corrosion or defected pins.
• An inspection of the circuit should be performed and the resistance across the terminals should be measured.
• Repeat the test at transmission connector if resistance doesn’t match the specifications which have been set by the manufacturer.

Common Mistakes When Diagnosing The P0960 Code

• A lot of people make a big mistake of attempting to diagnose the pressure control solenoid or transmission control module. Save yourself a big headache and make sure that you are addressing the defective harness or poor electrical connection before beginning your diagnosis.
• Common mistakes while diagnosing this trouble code are unnecessary and expensive replacements which usually happen when one don’t follow all the steps carefully.