P0902 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0902 can be described as Clutch Actuator Circuit Low. OBD-II trouble code P0902 and related codes P0900, P0901, and P0903 are associated with the clutch actuator circuit. The engine control module, powertrain control module or the transmission control module monitors this circuit depending upon the particular automobile.

Don’t worry if P0902 error code is triggering again and again. We offer wide range of auto parts at affordable prices to our dear customers. This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another. This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code.

What causes this problem with the Clutch Actuator Circuit Low?

• Imperfect clutch actuator
• The clutch actuator circuit might be opened
• The ground might be loose or disconnected
• Unusable solenoid
• Malfunctioning TCM or PCM

1. Car Battery - Do you remember when was the last time you got your car Car Battery checked up? A dirty Car Battery can cause a lot of issues like displaying P0902 code.
2. Engine Control Module - Poor Engine Control Module can cause a lot of difficulties, so why not get it replaced at time?
3. Powertrain Control Module - Are there some faults in your Powertrain Control Module? Don’t waste time and get them replaced or else P0902 code can turn up.
4. Auto Transmission Control Module - OBD Code P0902 can appear because of faulty Auto Transmission Control Module.
5. Timing Gear - Everything is fine with Auto Transmission Control Module and still P0902 code triggering? Then you must get your Timing Gear checked.
6. Auto Transmission Shift Solenoid - There can be some issues with the PCM due to which you may see P0902 code appearing over and over again. Visit us to buy best quality Auto Transmission Shift Solenoid online.

Our main motive is to achieve customer satisfaction and that’s why we will help you to diagnose P0902 code by mentioning some major symptoms below:

Common Symptoms

• Check engine light might come into signal
• Bad acceleration
• Diminishing fuel economy

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0902:

• The transmission control module should be reprogrammed
• You must fix the defective clutch
• Repair or replace the quirky solenoid
• The malfunctioning powertrain control module should be repaired or replaced as per the need

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of worm gear, planetary gear, battery connectors, car gear, gear module, solenoid engine and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

The clutch actuator cylinder is the metal rod which would connect to your pedal every time you depress the pedal to engage the gears. First of all a visual inspection should be done by a mechanic. He should inspect the unplugged harness connections as well as corrosion or loose wires on your connectors. Make sure to start by checking the wiring and connectors in your automobile. This can be done by utilizing a digital volt/ohmmeter and an OBD-II scanner. Now once the inspection has been completed, then you should mend or restore the faults in the wiring as well as connectors. A scanner should be used by a professional technician to notice the freeze frame data, to assemble details about the code. The mechanic can also check to see if there is presence of additional trouble codes. Now if there are a number of codes, then they should be addressed in the same order in which they are appearing on the scanner. After that the mechanic should reset the trouble codes, restart the vehicle, and check to see if the code remains detected. If it does not, then the code was likely triggered incorrectly, or represents an intermittent issue.