P0900 - OBD Trouble Code

<<See All OBD Codes

The trouble code P0900 can be defined as Clutch Actuator Circuit/Open. The clutch or clutches are engaged or disengaged on a semi-automatic transmission by the clutch actuator circuit. It all depends upon the particular automobile as well as its configuration, a lot of sensors as well as related constituents are needed to fulfil this task. Two hydraulic clutches are incorporated by some configurations. One is for even gears and other one is for odd gears. The total number of gears would vary from 6 to 9 on latest automobiles. 

It is always good to learn more! That is the reason why we are here to help you out in gaining more knowledge about the P0900 error code. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

What causes this problem with the Clutch Actuator Circuit/Open?

• Motion or travel sensors failing in the clutch
• There can be inoperative wires
• The electrical connectors might be corroded
• There can be some electrical failures inside the actuator solenoids or motors
• Some issues related to the loss of ground

1. Auto Transmission Control Module - Did your mechanic just found out that there is some fault in the Auto Transmission Control Module? Buy top-notch Auto Transmission Control Module from us at economical prices. 

2. Auto Transmission Shift Solenoid - A broken Auto Transmission Shift Solenoid can cause a lot of issues. It would be nice if you get it replaced on time.

3. Timing Gear - Everything is fine with the engine control module and still OBD code P0900 flashing? Then there is definitely some fault with the Timing Gear. Get it checked and replace if needed.

4. Car Battery - Battery is an important car part which should never be neglected. May be there is some fault in it due to which P0900 code may start flashing.

5. Powertrain Control Module - A faulty Powertrain Control Module can be troublesome. You can always rely on us as we have best auto parts for our customers.

6. Engine Control Module - If everything is alright with Auto Transmission Shift Solenoid, then there is surely some defect in Engine Control Module. Get it replaced before the situation gets worse.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0900 code by mentioning some major symptoms below:

Common Symptoms

• The engine might start stalling after the failure in the control system
• The engine does not start
• The transmission might start entering into limp mode
• The transmission may get stuck in one gear, but would not enter into limp mode

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0900:

• It is essential to restore the flawed PCM terminals
• You must fix the defective wiring or connectors
• Rehabilitate the defaults in the clutch actuator

However, if you face any issue then we have stocked a wide range of best priced worm gear, planetary gear, battery connectors, car gear, gear module, solenoid engine and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• The P0900 error code can be diagnosed by utilizing an OBD-II trouble code scanner.
• A scanner should be used by a professional technician to notice the freeze frame data, to assemble details about the code.
• The mechanic can also check to see if there is presence of additional trouble codes.
• Now if there are a number of codes, then they should be addressed in the same order in which they are appearing on the scanner.
• After that the mechanic should reset the trouble codes, restart the vehicle, and check to see if the code remains detected.
• If it does not, then the code was likely triggered incorrectly, or represents an intermittent issue.
• Examine the PCM terminal voltage.
• Investigate the condition of the PCM terminal.
• Carefully check the clutch actuator circuit.
• You should monitor the clutch actuator harness and connector.
• Make sure to observe the clutch actuator assembly.

Common Mistakes When Diagnosing The P0900 Code

• A big mistake which is made by a number of people is to simply fix the PCM terminal voltage issue without performing a proper inspection as there can be issue with some other auto part like the clutch actuator. The actual fault might be within the transmission fluid level or condition. It might also be related to a defective shift solenoid circuit, rather than the solenoid itself. One another big mistake which they might make is that they may not use the OBD-II scanner.