P084B OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P084B can be defined as Transmission Fluid Pressure Sensor/Switch "H" Circuit Range/Performance.

The mechanical transmission pressures are converted by the TFPS into an electrical signal for the powertrain control module or transmission control module. Other controllers utilizing the vehicle's data communication bus are informed by the PCM/TCM.

It is always good to learn more! That is the reason why we are here to help you out in gaining more knowledge about the P084B error code. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

What causes this problem with the Transmission Fluid Pressure Sensor/Switch "H" Circuit Range/Performance?

• The signal circuit to the TFPS sensor might be opened
• There can be short to voltage in the signal circuit to the TFPS sensor
• Issue of short to ground in the signal circuit to the TFPS sensor
• There can be inoperative TFPS Sensor
• Some issues related to the internal mechanical transmission issue
• Unusable PCM
• Imperfect transmission fluid pressure sensor/switch 'H'
• Transmission fluid pressure sensor/switch 'H' harness might be opened or shorted
• Bad electrical connection in the transmission fluid pressure sensor/switch 'H' circuit

1. Electronic Control Unit - Did your mechanic just found out that there is some fault in the Electronic Control Unit? Buy top notch Electronic Control Unit from us at economical prices.
2. Auto Transmission Shift Solenoid - A broken Auto Transmission Shift Solenoid can cause a lot of issues. It would be nice if you get it replaced on time.
3. Powertrain Control Module - Everything is fine with the Auto Transmission Control Module and still OBD code P084B flashing? Then there is definitely some fault with the Powertrain Control Module. Get it checked and replace if needed.
4. Engine Control Module - Engine Control Module is an important car part which should never be neglected. May be there is some fault in it due to which P084B code may start flashing.
5. Body Control Module Component - A faulty Body Control Module Component can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Auto Transmission Control Module - If everything is alright with PCM, then there is surely some defect in Auto Transmission Control Module. Get it replaced before the situation gets worse.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P084B code by mentioning some major symptoms below:

Common Symptoms

• Rising fuel consumption
• Visibility in the malfunction indicator light
• Transmission might not shift accurately
• Check engine light might come into signal
• Change in shift condition
• Motor vehicle begins off in 2nd or 3rd gear with limp in mode

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P084B:

• Rehabilitate the defaults in the body control module component
• The malfunctioning powertrain control module should be repaired or replaced as per the need
• It is essential to restore the flawed engine control module
• Repair or replace the quirky auto transmission control module
• You must fix the defective electronic control unit
• Make sure to mend the faulty auto transmission shift solenoid

Here are some steps which you should follow in order to diagnose this fault code:

• Inspect for technical service bulletins which pertain to the vehicle, symptoms, and codes. There can be some situations where this can save a lot of your precious time in the long run by pointing you in the correct way. Your issue may be a familiar issue with a well known fix put out by the manufacturer and can help a lot in save your precious time as well as money during the process of diagnosis. A great example of this would be if there are any known power related codes set along with the P084B, or if there is more than one pressure sensor/switch code set. If this is the situation, then you should start your diagnosis with the power related fault code first, or with the multiple code diagnosis first, as this may be the reason why P084B code is appearing.
• After that the Transmission Fluid Pressure Sensor/Switch should be located on your specific vehicle. The TFPS is generally present attached to the side of the valve body inside the transmission; although sometimes it may be found screwed into the side of the transmission case/body itself. Now once you have located it, the connector and wiring should be visually inspected. Carefully search for scraping, rubbing, bare wires, burn spots or melted plastic. The connector should be pulled apart and carefully inspect the terminals inside the connector. You must check if they look burned or have a green tint which would indicate corrosion, especially if they are attached outside the transmission case.
• An electrical contact cleaner should be utilized and a plastic bristle brush if cleaning of the terminals is required. Allow it to dry and apply electrical grease where the terminals contact. Then you should use a scan tool, thn clear the diagnostic trouble codes from memory, and check if P084B code returns. Now if you find out that it is not appearing, then the connections have some quirks.

Common Mistakes When Diagnosing The P084B Code

• Non observance of the transmission fluid pressure sensor
• Transmission control module might start failing
• Less transmission fluid level
• Issues related to the wiring