P0762 OBD Error Code: Problem & Solutions

<<See All OBD Codes 

A number of shift solenoids are included in a lot of automatic transmissions, and it all depends upon the number of gears which are inside.

The fault code P0762 can be identified as Shift Solenoid C Stuck On.

The fault codes which are related to this, the "C" solenoid, are codes P0760, P0761, P0763, P0764, P0765, P0766, P0767, P0768 and P0769. When this trouble code starts appearing, it would result in the illumination of the check engine light. If there is an overdrive or some other transmission warning lamp, then it might also start flashing up.

What causes this problem with the Shift Solenoid C Stuck On?

• Quirky powertrain control module
• The transmission filter might be dirty or clogged
• Insufficient fluid level
• Faults in the transmission valve body
• Polluted fluid
• Unusable shift solenoid
• Broken connector
• Defective wiring
• Confined hydraulic passages
• Internal damage in the transmission

1. Automatic Transmission Sensor - Do you remember when was the last time you got your car Automatic Transmission Sensor checked up? A dirty Automatic Transmission Sensor can cause a lot of issues like displaying P0762 code.
2. Electronic Control Unit - Poor Electronic Control Unit can cause a lot of difficulties, so why not get it replaced at time?
3. Auto Transmission Shift Solenoid - Are there some faults in your Auto Transmission Shift Solenoid? Don’t waste time and get them replaced or else P0762 code can turn up.
4. Powertrain Control Module - OBD Code P0762 can appear because of faulty Powertrain Control Module.
5. Engine Wiring Connectors - Everything is fine with Powertrain Control Module and still P0762 code triggering? Then you must get your Engine Wiring Connectors checked.
6. Engine Wiring Harness - There can be some issues with the Engine Wiring Harness due to which you may see P0762 code appearing over and over again. Visit us to buy best quality Engine Wiring Harness online.
7. Body Control Module Component - A lot of issues can arise do to defective Body Control Module Component. Did you just see P0762 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.

Our main motive is to achieve customer satisfaction and that’s why we will help you to diagnose P0762 code by mentioning some major symptoms below:

Common Symptoms

• Transmission sliding
• Transmission might start overheating
• Problem of transmission catches in gear
• Overall fuel economy can start declining
• There can be engine misfires
• Vehicle might start entering the limp mode
• Flashing up of the check engine light

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0762:

• Repair or replace the flawed transmission valve body
• If you find out that the transmission filter is dirty or clogged, then it should be repaired or replaced
• Correct the malfunctioning shift solenoid
• Make sure that you repair the defective wiring
• Inspect the internal failure in the transmission
• Correct the insufficient fluid level
• The faulty powertrain control module should be repaired or replaced

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of engine light, transmission filter, transmission valve body, torque converter, battery connectors, transmission oil, valve body, engine light, transmission fluid, transmission sensor and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• Inspect for technical service bulletins which pertain to the vehicle, symptoms, and codes. In some circumstances this can save a lot of time in the long run by pointing you in the right direction. You can always check the vehicle records to verify the last time that the filter and fluid was changed if possible.
• Initial step is to make sure the fluid level is correct and inspect the condition of the fluid for contamination. After that perform visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots should be performed.
• Next is to check the connectors and connections for security, corrosion and damaged pins. This process must include all wiring and connectors to the transmission solenoids, transmission pump and the PCM. It depends upon the configuration; the transmission linkage should be inspected for security and binding issues.
• The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multimeter and the specific technical references for the vehicle. Voltage requirements will vary based of the specific year and model of the vehicle. You should follow the specific troubleshooting chart for your vehicle.
• Continuity checks should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.

Common Mistakes When Diagnosing The P0762 Code

• Low transmission fluid level
• Quirks in the transmission shift solenoid
• Transmission control module might start failing
• Wiring related issues