P0760 - OBD Trouble Code

<<See All OBD Codes 

Fault code P0760 can be defined as Shift Solenoid C Malfunction.

A number of shift solenoids are included in a lot of automatic transmissions, and it all depends upon the number of gears which are inside. When this trouble code starts appearing, it would result in the illumination of the check engine light. If there is an overdrive or some other transmission warning lamp, then it might also start flashing up.

The main function of the shift solenoid circuit is for the PCM to monitor the shift solenoids to manage the movement of fluid between various hydraulic circuits and change the transmission gear ratio at the appropriate time. The overall performance of the engine starts rising because of this process at the lowest RPM.

What causes this problem with the Shift Solenoid C Malfunction?

• Polluted fluid
• The transmission filter might be dirty or clogged
• The fluid level might not be sufficient
• Flaws in the PCM
• Faults in the transmission valve body
• The shift solenoid might not be working properly
• Corroded or damaged connector
• Some defects in the wiring
• Cramped hydraulic passages
• There can be an internal failure in the transmission

1. Auto Transmission Shift Solenoid - Did your mechanic just found out that there is some fault in the Auto Transmission Shift Solenoid? Buy top notch Auto Transmission Shift Solenoid from us at economical prices.
2. Engine Wiring Connectors - A broken Engine Wiring Connectors can cause a lot of issues. It would be nice if you get it replaced on time.
3. Powertrain Control Module - Everything is fine with the engine control module and still OBD code P0760 flashing? Then there is definitely some fault with the Powertrain Control Module. Get it checked and replace if needed.
4. Automatic Transmission Sensor - Automatic Transmission Sensor is an important car part which should never be neglected. May be there is some fault in it due to which P0760 code may start flashing.
5. Engine Wiring Harness - A faulty Engine Wiring Harness can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Body Control Module Component - If everything is alright with Engine Wiring Harness, then there is surely some defect in Body Control Module Component. Get it replaced before the situation gets worse.
7. Electronic Control Unit - P0760 code can display due to some issues in the Electronic Control Unit. So, it is very important to replace the defective Electronic Control Unit with us at equitable prices.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0760 code by mentioning some major symptoms below:

Common Symptoms

• Transmission sliding
• Transmission might start overheating
• Problem of transmission catches in gear
• Diminishing fuel economy
• Possible engine misfire
• Vehicle enters limp mode
• Illumination of the check engine light

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0760:

• If you find out that the transmission filter is dirty or clogged, then it should be repaired or replaced
• Correct the insufficient fluid level
• The faulty powertrain control module should be repaired or replaced
• Repair or replace the defective transmission valve body
• Correct the malfunctioning shift solenoid
• Make sure that you repair the defective wiring
• Inspect the internal failure in the transmission

However, if you face any issue then we have stocked a wide range of best priced engine light, transmission filter, engine light, transmission valve body, torque converter, battery connectors, transmission oil, valve body, transmission fluid, transmission sensor and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

First of all, you should research the Technical Service Bulletins (TSBs) for the specific vehicle by year, model and transmission before you start with the troubleshooting process for any malfunction.

In some circumstances this can save a lot of time in the long run by pointing you in the right direction. You can always check the vehicle records to verify the last time that the filter and fluid was changed if possible.

Fluid & Wiring Inspections

The first step is to make sure the fluid level is correct and inspect the condition of the fluid for contamination. After that perform visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots should be performed.

Next is to check the connectors and connections for security, corrosion and damaged pins. This process must include all wiring and connectors to the transmission solenoids, transmission pump and the PCM. It depends upon the configuration; the transmission linkage should be inspected for security and binding issues.

Advanced Steps

The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multimeter and the specific technical references for the vehicle.

Voltage requirements will vary based of the specific year and model of the vehicle. You should follow the specific troubleshooting chart for your vehicle.

Continuity Checks

Continuity checks should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data.

Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.

Common Mistakes When Diagnosing The P0760 Code

• Transmission control module might start failing
• Low transmission fluid level
• Some issues related to the wiring
• Faults in the transmission shift solenoid