Guide To P0676 OBD Error Code Solutions

<<See All OBD Codes

If you are experiencing unusual response of the throttle, lack of power forms the car engine, impact on the fuel economy, engine stalling and hard starts and frequent illumination of the Check Engine Light, it might be an indication of the OBD Code P0676 error.

OBD-II Code P0676 is defined as a Cylinder 6 Glow Plug Circuit/Open.

OBD code P0676 relates to the device diesels use to heat the cylinder head for a few seconds when attempting to start a cold engine called a glow plug. A diesel relies entirely on the momentary high level of heat through compression to spontaneously ignite the fuel. The glow plug in the #6 cylinder has failed. When a diesel engine is cold, the extremely high air temperature produced as the piston rises and compresses the air is quickly lost through heat transfer to the cold cylinder head. The solution comes in the form of a pencil shaped preheater known as a "glow plug." The glow plug is installed in the cylinder head very close to the point that initializes combustion, or the "hot spot." This could be in the main chamber or pre-chamber. When the engine management computer senses the engine is cold through the use of its oil and transmission sensors, it makes the decision to assist the engine in starting with the use of the glow plugs.

What causes this problem with the Cylinder 6 Glow Plug Circuit?

• Faulty cylinder 6 glow plug
• Cylinder 6 glow plug harness is open or shorted
• Cylinder 6 glow plug circuit poor electrical connection
• Faulty glow plug module
• PCM failure

1. Glow Plug - Check for faulty glow plug in cylinder 6 of the engine and replace it as required. Buy new glow plugs and replace faulty glow plug now!
2. Glow Plug Connector - Glow plug connector can also be faulty and must be replaced for proper functioning of the components. Buy new connector now!
3. Glow Plug Relay - Damaged relays can also be an issue to the glow plug performance. Buy new glow plug relay now!
4. Starter Relay - Starter relay can also be damaged and should be replaced as it will affect the ignition system of the vehicle. Replace old starter relay now!
5. Engine Wiring Connector - Check for faulty engine wiring and connector and replace as required. Buy new engine wiring connector from us.
6. Engine Control Module - OBD Error Code P0676 can also be due to faulty ECMs. It’s better to get the faulty electricals replaced as soon as possible.
7. Powertrain Control Module - PCM problem can lead the wrong OBD code flashing and getting stored in the system. Thus, replace all faulty Powertrain related parts with us.
8. Diagnostic Tool - In order to detect the error, one needs high grade diagnostic tools. Visit us today to buy quality diagnostic tools.

If you are facing OBD error code P0676, then there are significant common symptoms that can be felt or observed. We have worked out a list here to help you out in understanding this problem better.

Common Symptoms

• The PCM will set the code P0676
• The engine is hard to start or may not start at all in cold weather
• Lack of power and acceleration
• Engine may miss due to the colder than normal cylinder head temperature 
• No pre-heat periods

It is very important to fix the fault code P0676. So here are some ways with which you can correct this issue:

• Replacement of the Cylinder 6 Glow Plug
• Replacement of the electrical components in the system
• Replacement of the glow plug timer or relay

However, if you face any issue then we have stocked a wide range of best priced Glow Plug Relay, Glow Plug Timer, Electrical Component, Glow Plug Circuit, PCM, Engine, Starter Relay and more to help you out in fixing your car.

If you want to easily diagnose this fault code, then all you have to do is to follow the steps which are mentioned below:

• The P0676 code should be diagnosed with an OBD-II trouble code scanner. A trained technician will look at the freeze frame data on the scanner to assess the code, and to check for the presence of any other trouble codes.
• The mechanic will begin by visually inspecting the electrical components in the glow plug circuit. Any wires that are shorted, connectors that are open or corroded, or fuses that are blown will need to be replaced.
• Following the electrical inspection, the glow plugs will need to be checked, and possibly replaced. The mechanic can check the glow plugs by connecting one end of a fully charged battery to the glow plug, and the other end to the ground. If the glow plug is incapable of producing heat (or, conversely, heats so intensely that it turns red), then it is defective. The glow plugs can also be inspected with a digital volt/ohmmeter.
• The mechanic will first inspect the glow plug in cylinder 6, but all glow plugs should be inspected if the issue is not resolved. If the code remains detected following the glow plug inspections and replacements, then the timers and relays will require inspection.
• Reset the trouble codes, restart the vehicle, and check to see if the P0676 code remains. This allows the technician to know as soon as the issue is resolved.

Common Mistakes When Diagnosing the P0676 Code

• Glow plug control module failure
• Glow plug failure
• Starter relay failure
• PCM failure
• Engine wiring and connector faults
• Glow plug wiring harness failure