Error Code P054D: What It Means & What To Do?

<<See All OBD Codes

The fault code P054D can be defined as Cold Start B Camshaft Position Timing Over-Retarded Bank 2.

The variable camshaft timing position for over-advanced camshaft timing during cold start up is monitored by the powertrain control module. The test would fail when the camshaft timing will exceed a maximum calibrated value or remains in an advanced position.

Willing to learn more about the P054D trouble code? It is the engine control module which manages and monitors the vehicle's engine ignition system, mechanical positioning of the rotating assemblies, fuel injection, emission systems, exhaust, transmission, among countless other systems.

What causes this problem with the Cold Start B Camshaft Position Timing Over-Retarded Bank 2?

• Some quirks in the intake valve timing control solenoid valve
• The intake valve timing intermediate lock control solenoid valve might have some faults
• The signal pick-up portion of the camshaft might have accumulated debris
• The timing chain is incorrectly installed
• There can be some flaws in the crankshaft position sensor
• The camshaft position sensor might be defective
• Foreign matter might contaminate the oil groove for intake valve timing control

1. Crankshaft Position Sensor - There can be some issues with the Crankshaft Position Sensor due to which you may see P054D code appearing over and over again. Visit us to buy best quality Crankshaft Position Sensor online.
2. Engine Wiring Connectors - A lot of issues can arise do to defective Engine Wiring Connectors. Did you just see P054D code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Engine Control Module - Faulty Engine Control Module can be the reason why P054D code is flashing. Visit us to purchase top notch Engine Control Module online.
4. Cylinder Head Gasket - It is an important auto part which needs full care. A faulty Cylinder Head Gasket can be a reason behind the flashing up of P054D code.
5. Powertrain Control Module - OBD Code P054D can appear because of faulty Powertrain Control Module.
6. Camshaft Position Sensor - There can be some issues with the Camshaft Position Sensor due to which you may see P054D code appearing over and over again. Visit us to buy best quality Camshaft Position Sensor online.
7. Fuel Injection System Parts - Are you facing some faults in your Fuel Injection System Parts? Don’t worry and get them replaced or else P054D code can turn up.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Possible misfire on start-up
• Issues related to cold start
• The overall engine performance might be poor
• The fuel economy can start decreasing

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Accumulated debris in the signal pick-up portion of the camshaft should be cleared
• Install the timing chain properly
• If there are some flaws in the crankshaft position sensor, then it should be replaced
• Restore the camshaft position sensor
• Make sure that the defective intake valve timing control solenoid valve is repaired
• It is essential to replace the intake valve timing intermediate lock control solenoid valve

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of car oil filter, k&n filter, timing chain replacement, diesel injection, ac delco oil filter, hydraulic filter and many more. Now all your problems would vanish within no time.

We include basic steps below but refer to a vehicle year/make/model/powertrain specific repair guide for specific steps for your vehicle

• Check for any Technical Service Bulletins that could provide possible solutions for any problems since most vehicles have upgradeable software in their ECMs. If a replacement is required, it is best to use a brand-new factory ECM and to program the latest software
• This step will require you to take a trip to an authorized service center of the brand of your vehicle. Just remember that an ECM can easily be replaced when there was actually a defective engine sensor, which can be a result of an overlooked detail in the initial diagnosis
• This is the reason why professional technicians will follow some sort of flow chart when inspecting a trouble code to prevent a misdiagnoses. It's always a good idea to refer to your specific model's service information first
• It would be a good idea to test the camshaft leaks immediately as they can produce more issues down the road if left unattended. Refer to your service manual for specific diagnostic procedures as well as location of the components. Depending on what type of camshaft position sensor you have (e.g. Hall effect, Variable reluctance sensor, etc.), diagnostics will vary as per the make and model
• There should be power present at the sensor in order to monitor the shafts position. If found defective, replace the sensor, reset the codes, and then test drive the vehicle
• Given the fact that "cold start" is in the description of the code, you should probably take a look at your cold start injector. It also, may be mounted to the cylinder head and somewhat accessible. Injector harness' are extremely susceptible to drying up and cracking, due to conditions, causing an intermittent connection. And most likely a cold start issues as well
• Be very careful when you are disconnecting any injector connector, during diagnosing

Common Mistakes When Diagnosing The P054D Code

• Failure in the powertrain control module
• The engine oil might not meet the manufacturer's requirements
• Decrease in the engine oil level
• Failure in the variable valve timing actuator
• Variable valve timing solenoid might have some flaws

P054C - Cold Start "B" Camshaft Position Timing Over-Advanced Bank 2