Guide To P0361 OBD Error Code Solutions

<<See All OBD Codes

The P0361 fault code can be defined as Ignition Coil K Primary / Secondary Circuit Malfunction.

This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

Generally, all the modern engines rely on a coil on plug ignition system. This would mean that each and every cylinder has its own coil. The powertrain control module has control over these coils. If the coil would be right over the spark plug, then there would be no need for spark plug wires.

Every coil has two wires. Out of these the first wire is a battery feed and it is generally from the power distribution center. And on the other hand, the second wire is the coil driver circuit and it comes from the powertrain control module. The powertrain control module can ground or unground this circuit to activate or deactivate the coil. The PCM would also monitor this setup to inspect for any errors. If it detects an open or short in the driver circuit, then the P0361 trouble code would start appearing.

What causes this problem with the Ignition Coil K Primary / Secondary Circuit Malfunction?

• The connector might lock or it might be broken
• Defaults in the COP coil
• The COP driver circuit might be opened, grounded or shorted
• There can be a loose connection at the coil

1. Engine Wiring Harness - Did your mechanic just found out that there is some fault in the Engine Wiring Harness? Buy top notch Engine Wiring Harness from us at economical prices.
2. Battery Cable Replacement Terminal - A damaged Battery Cable Replacement Terminal can cause a lot of issues. It would be nice if you get it replaced on time.
3. Engine Wiring Connectors - Everything is fine with the engine control module and still OBD code P0361 flashing? Then there is definitely some fault with the Engine Wiring Connectors. Get it checked and replace if needed.
4. Powertrain Control Module - Powertrain Control Module is an important car part which should never be neglected. May be there is some fault in it due to which P0361 code may start flashing.
5. Fuel Pump - A faulty Fuel Pump can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Ignition Coil - If everything is alright with PCM, then there is surely some defect in Ignition Coil. Get it replaced before the situation gets worse.
7. Engine Control Module - P0361 code can display due to some issues in the Engine Control Module. So, it is very important to replace the Engine Control Module with us at equitable prices.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0361 code by mentioning some major symptoms below:

Common Symptoms

• There can be lack or loss of power
• The car engine might be harder to start
• Engine might hesitate
• The check engine light can start appearing
• Rough engine idle

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0361:

• The mechanic should replace the #11 ignition coil if they picked up a Hertz signal
• The next step would be to examine the wiring
• Replace or repair the damaged ignition coil
• If there is some issue in the PCM, then it should be restored

However, if you face any issue then we have stocked a wide range of best priced fusion, wiring diagram, battery connectors and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• A mechanic should use an OBD-II scanner to diagnose this fault code
• A qualified professional should also note any related codes that may have been stored too
• Now once the OBD-II fault codes have been resettled, the mechanic will want to take the vehicle on a road test and watch the sensor’s live data while driving
• Once the drive is over, they should also run a scan to see if the P0361 code comes back
• If it does, the mechanic will then need to check for any electrical wiring, connector or sensor issues.
• The technician will most likely need to use a Voltmeter in AC hertz scale to see if the #11 coil produces an Hz reading between 5 and 20

Common Mistakes When Diagnosing The P0361 Code

• The most common mistake which is made by a lot of technicians that they misdiagnose the problem and assume that a tune-up will be enough to get the vehicle back up and running
• There can be one big mistake that the tune-up might be long overdue, a thorough diagnosis should be performed first to make sure the true reason behind the problem is understood