P0353 - OBD Trouble Code

<<See All OBD Codes

The P0353 fault code can be defined as Ignition Coil “C” Primary/Secondary Circuit Malfunction.

The last digit to this fault code would indicate that there is a problem which is detected within the ignition process of cylinder number 3. The coil is a transformer which would revamp the lower voltage supplied by the battery into the higher voltage that spark plugs need to ignite the fuel for a successful combustion process. On an average 70,000 to 100,000 volts are produced by a coil pack on average.

A coil pack can be called as a coil on plug or an ignition coil which is used to convert the standard battery voltage into the higher voltage which is needed for the internal combustion process of a car engine. The P0353 fault code can be set if the engine control module would detect an issue with the ignition process of the coil pack. Now in this case, the coil pack which is found malfunctioning is situated above the cylinder number 3.

Do you wish to learn more about P0353 fault code? Then you have arrived at the correct place. Individual ignition coils are used by the ignition system on the vehicle for each cylinder. Each and every ignition coil is controlled by the engine control module. An ON/OFF signal is sent by the engine control module so that it can energize the ignition coil to create a spark at the spark plug when there is a requirement of spark at the cylinder.

What causes this problem with the Ignition Coil “C” Primary/Secondary Circuit Malfunction?

• There can be short to voltage or ground on COP driver circuit
• Issue of open on COP driver circuit
• There can be failed or failing ECU
• Defaults in the ignition coil 3
• There can be open or short in the coil wiring harness
• Electrical connection might be poor
• Leakage in the intake manifold vacuum
• Ignition coil 3 harness might be opened or shorted
• Loose connection at coil or broken connector locks
• The coil can be bad
• Defects in the powertrain control module
• Some quirks in the spark plugs or plug wiring
• The ignition coil might be faulty
• There can be a buildup of carbon in the throttle body air passages
• The idle air control valve or electronic body might turn out to be faulty
• There can be poor electrical connection in the ignition coil 3 circuit

1. Ignition Coil - Do you remember when was the last time you got your car Ignition Coil checked up? A defective Ignition Coil can cause a lot of issues like displaying P0353 code.
2. Powertrain Control Module - Poor Powertrain Control Module can cause a lot of difficulties, so why not get it replaced at time?
3. Engine Control Module - Are there some faults in your Engine Control Module? Don’t waste time and get them replaced or else P0353 code can turn up.
4. Fuel Ignition System - OBD Code P0353 can appear because of faulty Fuel Ignition System.
5. Engine Wiring Connector - Everything is fine with Powertrain Control Module and still P0353 code triggering? Then you must get your Engine Wiring Connector checked.
6. Spark Plug - There can be some issues with the Spark Plug due to which you may see P0353 code appearing over and over again. Visit us to buy best quality Spark Plug online.
7. Electronic Control Unit - A lot of issues can arise do to defective Electronic Control Unit. Did you just see P0353 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
8. Throttle Body - Faulty Throttle Body can be the reason why P0353 code is flashing. Visit us to purchase top notch Throttle Body online.

Our main motive is to achieve customer satisfaction and that’s why we will help you to diagnose P0353 code by mentioning some major symptoms below:

Common Symptoms

• There can be lack of power in the engine, especially under heavy load
• Car engine may idle roughly
• There can be hard to start condition of the engine
• Illumination in the malfunction indicator lamp
• Engine might misfire on acceleration
• Issue of engine hesitation

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0353:

• If you find out that there are damaged or corroded ignition coils, then they should be repaired or replaced
• Make sure that you replace damaged or faulty ignition coil wires and connectors
• All the codes should be cleared up, then you should test-drive the vehicle and rescan to see if any codes are reappearing
• You can always replace shorted or damaged wire to coil drive circuit
• The defected engine control module should be replaced

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of fusion, wiring diagram, battery connectors, fuse and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• An OBD-II scanner should be utilized to check for a stored P0353 trouble code
• Visually inspect all wires and connectors for signs of damage or corrosion
• Determine whether the engine misfire is a regular occurrence or intermittent
• Test the ignition coil C for loose or corroded prongs.
• Check ignition coil C for damaged or shorted wires or connectors
• Test Hertz signal to ignition coil C, if between 5 and 20 Hertz, coil is damaged
• Test voltage on coil driver circuit
• Test for resistance and continuity between ground and coil driver circuit
• The damaged or defective camshaft sensors should be checked

Common Mistakes When Diagnosing The P0353 Code

The P0353 fault code can start appearing because of some issues in the engine control module, so make sure that you have completely diagnosed all the possible wiring faults as well as other issues before you start diagnosing the engine control module.