P02E8 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The diesel intake air flow position sensor is generally bolted to the throttle body mounted to the intake manifold or in a tube which is present in the intake air stream. The DIAFPS sensor would convert the incoming airflow volume into an electrical signal for the powertrain control module.

The P02E8 trouble code can be defined as Diesel Intake Air Flow Position Sensor Circuit Low

This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code.

What causes this problem with the Diesel Intake Air Flow Position Sensor Circuit Low?

• There can be bad electrical connection in the diesel intake air flow position sensor circuit
• Some flaws in the diesel intake air flow position sensor
• Diesel intake air flow position sensor harness might be opened or shorted
• Throttle body assembly might be defective
• Quirks in the engine control module

1. Air Intake System - A faulty Air Intake System can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Mass Air Flow Sensor - If everything is alright with Intake Air System, then there is surely some defect in Mass Air Flow Sensor. Get it replaced before the situation gets worse.
3. Engine Control Module - P02E8 code can display due to some imperfection in the Engine Control Module. So, it is very important to replace the Engine Control Module with us at equitable prices.
4. EGR Valve Gasket - Do you remember when was the last time you got your car EGR Valve Gasket checked up? A defective EGR Valve Gasket can cause a lot of issues like displaying P02E8 code.
5. Powertrain Control Module - There can be some issues with the Powertrain Control Module due to which you may see P02E8 code appearing over and over again. Visit us to buy best quality Powertrain Control Module online.
6. Throttle Body - Are you facing some faults in your Throttle Body? Don’t worry and get them replaced or else P02E8 code can turn up

It is vital to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P02E8 here:

Common Symptoms

• There might be no regeneration of the diesel particulate filter to burn off the soot build up
• Problem of loss of power
• The indicator light on may start malfunctioning
• Low idle speed
• No EGR System operation

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• The defective mass air flow sensor should be replaced
• Make sure that you replace the engine control module
• If you find out that there are some defaults in the air intake system, then you must replace it
• The EGR valve gasket should be repaired or replaced as per the need

Parts Avatar Canada endeavours to fulfil all the needs of its consumer, that’s why we have a huge collection of top-quality k&n cold air intake, fuel pressure regulator, mass air flow sensor cleaner and many more at equitable prices. We won’t let you down in any way.

Here are some steps which you should follow in order to diagnose this fault code:

• If you find out that the P02E8 code is returning once again, then you must test the DIAFPS sensor and as well as the circuits which are associated with it.
• With the Key Off, you must disconnect the electrical connector at the DIAFPS sensor. Connect a digital voltmeter black lead to the ground terminal at the DIAFPS sensor wiring harness connector. Connect the red lead of the digital voltmeter to the signal terminal at the DIAFPS sensor wiring harness connector.
• Turn Key On engine off. The manufacturer’s specifications should be checked; voltmeter should read 5 volts. If not, then you must repair the signal or ground wire or the powertrain control module should be replaced

Common Mistakes When Diagnosing The P02E8 Code

• Faults in the powertrain control module
• Foible wiring
• Infirmity in the throttle body assembly