Error Code P0246: What It Means & What To Do?
OBD Code P0246 - Turbocharger Wastegate Solenoid A High
The wastegate is a turbocharged vehicle which is
the part of the system which would regulate the maximum boost pressure by
opening as well as closing so that it can divert exhaust. It would act as a
protection for the turbocharger as well as the engine.
Now if this code is set by a vehicle, then it
would mean that a signal has been received by the engine control module which
would indicate that the wastegate solenoid A circuit voltage does not fall
within the recommended specifications. There can be some other turbocharger or
the engine codes which can get stored along with the P0246 error code.
The P0246 fault code can be described as Turbocharger Wastegate Solenoid High.
Learn More About OBD Error Code P0246
The
wastegate solenoid would allow unneeded boost which has been generated by the
turbo or the supercharger to vent the system. The wastegate solenoid is controlled by the ECM, it will set P0246 code. The PCM might also disable the turbo or the supercharger to prevent further
damage to the system.
What causes this problem with the Turbocharger
Wastegate Solenoid High?
- The wastegate solenoid might be bad
- A stuck or impaired wastegate door
- There can be a short or open in the solenoid
harness
- The solenoid connectors can be corroded
- Some faults in the engine control module
Replace/Repair These Parts To Fix OBD Code P0246
- Engine Control
Module - Did your mechanic just found out
that there is some fault in the Engine Control Module? Buy top notch Engine
Control Module from us at economical prices.
- Knock Sensor - A broken Knock Sensor can cause a lot of issues. It would
be nice if you get it replaced on time.
- Indicator Lamp - Everything is fine with the engine control module and still OBD code P0246 flashing? Then there is definitely some fault with the Indicator Lamp. Get it checked and replace if needed.
- Wastegate Solenoid - Wastegate Solenoid is an important car part which should never be neglected. May be there is some fault in it due to which P0246 code may start flashing.
Symptoms Of OBD Error Code P0246
We care for our customers and that’s
why we can totally understand your problem. That’s the reason why we have
listed out some major symptoms behind the flashing up of OBD Code P0246. They
are mentioned here as follows:
Common Symptoms
- A malfunction in the wastegate solenoid circuit
- There can be poor acceleration
- Abnormal sounds from the turbocharger or pipes
- Smoke coming out from the exhaust
- There can be poor engine performance
- The engine may experience a boost condition while idling, which could cause stalling or rough idling
- An illumination in the malfunction indicator lamp
How To Correct P0246 Turbocharger Wastegate Solenoid A High
We have listed out some ways which
would help you to correct the OBD P0246
- The damaged wiring or connections to
the wastegate solenoid should be repaired properly
- You can always replace the faulty
solenoid
- Replace the engine control module
Now are you thinking that from where will you purchase these car parts? You have arrived at the right place. We at Parts Avatar care for our customers, that’s why we provide best quality of turbo boost, transmission slipping, electric turbo and boost controller at marketable prices.
Easy Diagnosis Of Engine Error OBD Code P0246
Here are some steps which you should
follow in order to diagnose this fault code:
- A scanner to the vehicle should be
connect to check for other codes and to record freeze frame data
- Then you must clear the codes and
then road test the vehicle to check if the code returns
- Address any co-existing DTCs in the
order in which they occurred
- It is very important to visually
inspect the wastegate solenoid and its surrounding circuitry and connections
- Examine the resistance and voltage
to be sure they match manufacturer’s specifications
- The vacuum lines should be checked
and wastegate door for sticking
- The wastegate door should be
visually observed and actuator rod while the vacuum pump is being activated
Common Mistakes When Diagnosing The P0246 Code
The most common diagnostic errors
may include replacing the wastegate solenoid without actually inspecting the
rest of the system, such as the wastegate door and linkage. If the wastegate
door is stuck, or connectors or wiring are compromised, replacing the solenoid
may only result in continued failure
It is also very important not to overlook any boost pressure sensor codes that are present along with P0246. If one is present, this should be repaired first before the wastegate solenoid A circuit is repaired