Guide To P0199 OBD Error Code Solutions

<<See All OBD Codes

Are you noticing Check Engine Light getting flashed on the dashboard? Is there an increase in the engine temperature leading to affected performance and fuel economy? All these can be an indication of some problem with the EOT sensor and system, thus cause OBD code P0199 error.

OBD code P0199 is defined as the Engine Oil Temperature (EOT) Sensor Intermittent issue.

OBD code P0199 gets stored whenever the Powertrain Control Module detects an intermittent fault in the engine oil temperature sensor. The PCM receives voltage signal coming from the oil temperature sensor that helps him take decisions for proper functioning of the engine and its performance. When the signal is intermittently out-of-range, P0199 is set.

This condition can cause the ECU to trigger the failsafe mode to protect the engine from further damage and a diagnostic trouble code (DTC) as an indication to the specific problem. This failsafe mode can remain in effect until the P0199 fault is resolved and the sensor starts sending signals normally to the PCM.

What causes the problem of Engine Oil Temperature (EOT) Sensor Intermittent?

• Engine Oil Temperature sensor faulty
• Engine Oil Temperature sensor harness is open, short, damaged or broken
• Poor electrical connection to the sensor and the circuit

1. Engine Oil Temperature Sensor - This is the most common cause of the issue and has to be replaced if needed to. Buy new sensor from us today.
2. Engine Control Module - Check for any faults in the ECM components and replace that as needed. Buy quality components form us.
3. Oil Temperature Gauge - Sometime it’s the gauge that is problematic and is not flashing the reading correctly which can lead to misdiagnoses. Always check and change faulty gauge first.
4. Diagnostic Tools - A professional mechanic will use high grade diagnostic tools to correct P0199 error issue. Explore now!
5. Thermistor - If it is not functioning to tits capacity, replace it immediately. Buy from us today!
6. Powertrain Control Module - Replace faulty PCM components and repair or reprogram if needed so that it reads and interprets the data correctly.

Since this code is likely points to the problem on the EOT sensor circuit, there may not be any noticeable big symptoms at present and even if there are any can we considered as general problems by the driver. However, the MIL (Malfunction Indicator Light) will likely be on and the car may exhibit some drivability problems.

• Replace engine oil temperature sensor, if found faulty
• Check and replace bad sensor wiring harness
• Repairing poor electrical connections to the sensor and circuit 

At Parts Avatar Canada, you can find all the replacement and performance parts you need to get rid of any OBD Code problem at the best prices in the market and from the best brands, for any make and model. Explore now! 

The step by step analysis and diagnosis is recommended by a qualified technician using high grade diagnostic tools to check for all the problems and solving them.

• You require a scanner or a code reader and a digital volt ohmmeter to successfully diagnose this code. Begin your diagnosis by visually inspecting all wiring and connectors to the sensor.
• Search for shorted or burned wiring and connectors and replace them.
• Connect the scanner to the diagnostic connector and record all stored trouble codes and freeze frame data. After the codes are cleared, operate the vehicle to see if the code returns. If the code fails to immediately return, you may have an intermittent condition.
• Check for the problem with the EOT sensor and circuits and diagnose to see with the error returns. Perform a test on the engine oil temperature sensor using the scan tool. This scan tool will monitor changes in voltage and readings over time and will allow the technician to recognize any underlying issues. Replace the EOT sensor if required and check if the code returns again or the sensor has gone back to normal functioning.
• If everything else is fine, then the problem can be with the PCM. Replace the PCM if required and check if the code reappears. You can also check by reprogramming the PCM to see if it is performing perfectly or not.

Common Mistakes When Diagnosing The P0199 Code

Some of the common mistakes done while changing diagnosing the OBD code P0199 are:

• Improper assessment of the EOT sensor failure
• Simply replacing the Powertrain Control Module (PCM) without considering other possibilities of problem.
• Not noticing the damaged or loosened wiring and circuit problems.