Guide To P0134 OBD Error Code Solutions

<<See All OBD Codes

The P0134 error code can be described as oxygen sensor circuit no activity detected (bank 1 sensor 1). This would mean that there is some issue in the front oxygen sensor on bank 1, as the O2 sensor is not active.

The powertrain control module is a car component and is also a control unit which would combine with the engine control module as well as transmission control unit. It is the brain of the engine’s control system. In the relation to the fault code P0134, the powertrain control module would provide the baseline voltage of around 450 mV on the O2 sensor signal circuit.

What causes this problem with the O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)?

• There can be some defects in the heater circuit
• A wire might be broken or disconnected from the oxygen sensor
• The issue of corrosion in the connectors
• A leakage in the engine vacuum
• Defective powertrain control module

1. Oxygen Sensor - There can be some issues with the Oxygen Sensor due to which you may see P0134 code appearing over and over again. Visit us to buy best quality Oxygen Sensor online.
2. Mass Air Flow Sensor - A lot of issues can arise do to defective Mass Air Flow sensor. Did you just see P0134 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Manifold Absolute Pressure Sensor - Faulty Manifold Absolute Pressure sensor can be the reason why P0134 code is flashing. Visit us to purchase top notch Manifold Absolute Pressure sensor online.
4. Exhaust Parts - Make sure that there is no defect in the car Exhaust parts. A faulty Exhaust System parts can be a reason behind the flashing up of P0134 code.
5. Powertrain Control Module - OBD Code P0134 can appear because of faulty Powertrain Control Module.
6. Engine Control Module - Are there some faults in your Engine Control Module? Don’t waste time and get them replaced or else P0134 code can turn up.
7. Fuel Pump - OBD Code P0134 can appear because of faulty Fuel Pump.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Illumination of the check engine light on the dashboard and the engine may start stalling
• You may experience the feeling that your car is running rough or that it is idling poorly
• You may experience a smell something similar to rotten eggs or see black smoke billowing from the exhaust
• Sometimes a driver might not notice any of these symptoms, other than the illumination of the check engine light, but this is a rare

We have listed out some ways which would help you to correct the occurrence of OBD Code P0134. They are mentioned here as follows:

• A scanner should be used by the technician to validate the fault code. Once the fault code has been validated, you should reset it and a test drive should be performed. If the check engine light returns with the same fault code, then further inspection should be done
• Make sure that you inspect the wires and connectors for any damage. If the wires and connectors are damaged, they should be repaired or replaced. Then reset fault code and test drive
• If you find out that the check engine light is illuminating and the technician gets the same code, then the car oxygen sensor should be replaced
• If you find out that the P0134 trouble code comes back after replacing the oxygen sensor, then you must inspect the exhaust pipe and heater fuse to rule out possible damage of the two

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of catalytic converter, relay wiring harness, battery connectors and many more. Now all your problems would vanish within no time.

• If you want to diagnose the P0134 code, then you can always visit a technician who will use an OBD-II scanner to diagnose this fault code. The freeze frame data should be captured in order to determine when the code was first set. At this point, the code should be reset and the vehicle should be taken out for a test drive.
• While the vehicle is out for test driving, the vehicle needs to reach normal operating temperature in order to see if the code comes back. If the fault code does come back, the wiring that goes to the oxygen sensor and grounds needs to be inspected. While inspecting the technician will look for breaks and corrosion. Live data should be observed in an effort to determine whether the millivolt valves are going low to high.
• Make sure that you inspect the oxygen sensor in order to determine whether it has power going to it and that it is receiving the proper signal voltage from the power control module

Common Mistakes When Diagnosing The P0134 Code

• There can be some issues in the oxygen sensor/air fuel ratio sensor
• Faulty oxygen sensor/air fuel ratio sensor heater circuit
• Leakage in the exhaust system
• Intake air system might start leaking
• Low fuel pressure
• Defective engine coolant temperature sensor
• There can be some default in the sensor wiring or circuit problem
• PCM software needs to be updated
• Defects in the powertrain control module