Error Code P011C: What It Means & What To Do?
Obd code P011C - Charge Air Temperature/Intake Air Temperature Correlation Bank 1
Always make sure
that there should be no faults in the intake air temperature sensor 1 and it
should function properly. Now the question which would be there in your mind is
“WHY?” The answer to this is that if you will not take care of this, then OBD
Code P011C would set up.
The engine
control module would detect a state that the difference between the temperature
of the intake air temperature sensor 2 and its estimated temperature calculated
by the engine control module from the intake air temperature 1 as well as
turbocharger boost sensor.
Learn More About OBD Error Code P011C
The OBD P011C can be defined as a Charge Air Temperature/ Intake Air Temperature Correlation. The charge air temperature sensor measures the overall temperature of the air which is going through the charge air cooler. The main function of the intake air temperature sensor is to measure the temperature of the air which is going into the car engine. The two readings that would determine if sensors are reading properly and correctly are compared by engine control module. If the PCM determines that there is an irrational reading in one of the sensors, then the P011C error code would appear.
What causes this problem with the Charge Air
Temperature/Intake Air Temperature Correlation Bank 1?
- There
can be some faults in the intake air temperature sensor 1
- Defects
in the intake air temperature sensor 2
- IAT Sensor 1 or IAT Sensor 2 harness may be opened or shorted
- Bad
electrical connection in the IAT Sensor 1 or IAT Sensor 2 circuit
Replace/Repair These Parts To Fix OBD Code P011C
- Intake air
Temperature Sensor - Do you remember when was the last
time you got your car Intake air Temperature Sensor check-up? A damaged Intake
air Temperature Sensor can cause a lot of issues like displaying P011C code.
- Mass Air Flow
Sensor - Everything is fine with turbocharger/supercharger and still
P011C code triggering? Then you must get your Mass Air Flow Sensor.
- Engine Control
Module - A lot of issues can arise do to
defective Engine Control Module. Did you just see P011C code flashing? Now you
know the reason why it is appearing. Get it inspected and replaced on time.
- Thermistor - Common cause behind this P011C error code can be some fault in Thermistor. So, it will be a good decision to replace them now.
- Powertrain
Control Module - The P011C code can also arise due to
some issues in Powertrain Control Module. So, it is advised to replace them as
soon as possible.
Symptoms Of OBD Error Code P011C
Our
main motive is to achieve customer satisfaction and that’s why we will help you
to diagnose P011C code by mentioning some major symptoms below:
Common Symptoms
- Decrease
in the overall engine performance
- Excessive
rich or lean exhaust
- Delayed engine start-up. This can occur especially during cold
- The
fuel efficiency may start diminishing
How To Correct P011C Charge Air Temperature/Intake Air Temperature Correlation Bank 1
Have a look at
some ways with which you can correct the P011C code:
- The intake air
temperature sensor 1 should be repaired or replaced
- Replace the engine control module
There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of flywheel, wheel bearing, egr valve and many more. Now all your problems would vanish within no time.
Easy Diagnosis Of Engine Error OBD Code P011C
Before
you start to diagnose P011C fault code, you must have some basic diagnostic
tools like a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a reliable
vehicle information source.
Make
sure that you begin diagnosing this CAT sensor related code by checking that
there should be no obstructions in air flow across the intercooler.
The
next step is to visually inspect all CAT/IAT system wiring and connectors as
they should be in order and there should be no obstructions by the intercooler
and the car air filter should be clean. These repairs should be made as per the
requirement.
The
other step is to connect the scanner to the vehicle diagnostic port and all the
stored codes should be retrieved as well as freeze frame data. Freeze frame
data could be best described as a snapshot of the exact circumstances which
were occurring at the time of the malfunction which led to the stored code
P011C. You can always note down this information as it would be helpful during
the proceeding of the diagnosis.
Common Mistakes When Diagnosing the P011C Code
- Failure
in the charge air temperature
- There
can be some default in the intake air temperature sensor
- Powertrain Control Module may start failing
- Some
wiring issues can also arise