Error Code P0064: What It Means & What To Do?
OBD Code P0064 - HO2S Heater Control Circuit High (Bank 2 Sensor 3)
<<See
All OBD Codes
Is your Check
Engine Light On? Is the car experiencing loss of engine power? Is there black
smoke coming from the exhaust pipe? If these are the problems you are facing,
then there might be indicative of OBD Code P0064 error.
OBD-II Code
Decreased engine performance is defined as a HO2S Heater Control Circuit High.
Learn More About OBD Error Code P0064
Indicates
that there is an abnormally high voltage or resistance present in the heater
control circuit of oxygen sensor (bank 2 sensor 3). The oxygen sensor
measurements only become accurate when the sensor reaches a temperature of 600
degrees or above.
Oxygen
sensor measures the oxygen content in the exhaust gases as they leave the
combustion process of the engine. The oxygen sensor must attain a certain
temperature for this information to be accurately read and transmitted to the
Power Control Module (PCM) as increase in temperature increases the process
speed. The PCM sends a voltage to the heater circuit of the oxygen sensor. The
sensor turns most of that voltage into heat but also uses the voltage as a way
to communicate the air-fuel ratio to the PCM. When the PCM detects that the
heater wire is not operating, it sets OBD code P0064.
What causes problem of HO2S Heater Control Circuit High
(Bank 2 Sensor 3)?
- Excessive
carbon builds up on the oxygen sensor, restricting accurate measurement
- Heated
Oxygen Sensor Bank 2 Sensor 3 faulty
- Damaged
wiring and harness
- Open
in the heater control circuit
- Faulty/damaged
Mass Airflow Sensor (MAF)
- Vacuum
or excessive exhaust leaks
- Corroded or damaged Connections
- Failure
of Powertrain control module
Replace/Repair These Parts To Fix OBD Code P0064
- Oxygen Sensor - Damaged oxygen
sensor will not be able to collect the correct readings and send wrong
information to the PCM. Thus, replace faulty sensors now!
- Mass Air Flow
Sensor - If the information sent to the PCM is
wrong, it will affect the engine performance greatly. Buy new MAF sensor today!
- Oxygen Sensor
Connector - A faulty Oxygen Sensor Connector will
affect the functioning of the oxygen sensor and thus needs to be replaced
immediately.
- Powertrain Control
Module - PCM needs to interpret the
information correctly so that the right air to fuel ratio can be achieved.
Replace faulty PCM components immediately.
- Diagnostic Tools - Use professional level tools to detect and correct the OBD code problems. Buy now!
- Battery & Parts - There can also
be issue with the car battery that can lead to engine problems. Replace faulty
battery parts now!
Symptoms Of OBD Error Code P0064
The
P0064 code will illuminate a Check Engine Light on the instrument panel/dash.
The following symptoms can indicate the presence of OBD Code P0064 that is
being flashed and stored in the PCM and can lead to the engine going into
failsafe mode.
Common Symptoms
- Service
engine light or Check Engine Light illumination
- Reduced
Engine power and performance
- Lean
or Rich Engine Condition
- Faulty
Powertrain Control Module
- Black
smoke from the Tailpipe
- Gas
leakage smell from the Exhaust
- Increased Exhaust leaks
- Engine
vacuum leaks
How To Correct P0064 HO2S Heater Control Circuit High (Bank 2 Sensor 3)
- Scan
the computer system for OBD code errors stored in the PCM
- Check
for vacuum leaks and holes in the exhaust system
- Replace
faulty oxygen sensor
- Check
electrical wiring and connections
- Clear diagnostic codes and test drive the car to see if the code reappears
At
Parts Avatar Canada, find the best quality replacement and performance parts at the best price in the market to correctly diagnose the
OBD Code P0064 error.
Easy Diagnosis Of Engine Error OBD Code P0064
- Take
the help of a qualified technician to use a scan tool and confirm whether P0064
is present.
- Find
and freeze frame data with the code. Then, clear the code.
- Take
the vehicle on a test drive under the same conditions.
- If
the code reappears, perform a visual inspection of the bank 2 sensor 3 and its
wiring.
- If
the wiring is okay, the sensor itself will be tested to confirm operation.
- If
the HO2S is functioning properly, the technician must check the Engine Control
Unit for any faults and damages.
- If
all the components are working properly, check for faults in the PCM and
replace or reprogram according to the situation.
Common Mistakes When Diagnosing The P0064 Code
It is important to inspect all the components properly before directly jumping to the PCM or the sensor for the diagnosis. This way you can avoid the OBD error from reappearing as well as save on future costs as repairs of faults in the wirings are much cheaper that replacing a perfectly healthy sensor or PCM without knowing the main reason of the problem.
- Replacing
the wrong oxygen sensor by misinterpreting the order
- Mass
Air Flow sensor dirty and not inspected properly
- Not checking for leakages causing
damages to the oxygen sensor. Thus, proper diagnosis is necessary in correct
order to properly diagnose OBD code P0064 error.