Error Code P0026: What It Means & What To Do?
OBD Code P0026 - Intake Valve Control Solenoid Circuit Range Performance Bank 1
Is
your Car’s ECM activating the intake valve solenoid? Do you find the wiring or
connections to the intake valve solenoid be shorted or open? Or are there some
defects in the engine control module? This might be the indication of problems
with the intake valve solenoid of the car which in other words can be an OBD
P0026 error. Diagnostic trouble code P0026 can be defined as the intake valve
control solenoid circuit range/performance (Bank 1) is not correct.
Learn More About OBD Error Code P0026
If
the engine control module has determined that the variable valve lift solenoid
for the intake valves for bank 1 are taking too long to engage or are not
engaging at all, then the OBD II error code P0026 would start indicating.
What causes this problem with the Intake Valve Control
Solenoid Circuit Range/Performance?
- The
ECM may activate the intake valve solenoid, but the valves would not change to
the high lift position
- The
intake valve solenoid may have an open or short circuit
- The
wiring or connections to the intake valve solenoid is shorted or open
- There
might be some defects in the ECM
Replace/Repair These Parts To Fix OBD Code P0026
- Variable Valve
Timing - Are you facing OBD
error P0026 code? You can always get this issue resolved with new variable
valve timing. Purchase top notch Variable Valve Timing from us at best prices.
- Variable Control Solenoid - Common
cause behind this P0026 error code can be some fault in the variable control
solenoid. So, it will be a good decision to replace them now.
- Powertrain Control
Module - There are some chances
that the powertrain control module may appear faulty and due to that P0026 code
may come. So, it better not to take any risk as you can always purchase brand
new powertrain control module online with us.
- Engine Control
Module - Facing issues with
engine control module? Buy new engine control module and get rid of this issue.
- Intake Valve
Solenoid - May be your timing
belt is good and there are some issues with the intake valve solenoid. Then
don’t waste time and purchase best intake valve solenoid with us.
Symptoms Of OBD Error Code P0026
Symptoms
of P0026 code are roughness at idle, choppy acceleration, decrease in the
engine performance and substandard fuel efficiency. Have a look at some other
symptoms mentioned below:
Common Symptoms
- The
lack of power would be experienced by the engine
- The
engine may start running roughly or stall if one of the two intake camshafts
are stuck in a high valve lift position
- The
engine will run very erratically and it all depends on the intake valves failed
position
- The check engine light will start appearing indicating that there is some
issue
How To Correct P0026 Intake Valve Control Solenoid Circuit Range/Performance Bank 1
Examining the below mentioned components can be the most
common solution to correct the OBD Code P0026 error;
- Firstly,
you must clear the fault codes and then perform a road test to try and verify
failure
- The
valves should work okay and this could be tested by installing the solenoid and
then you can replace the intake lift solenoid
- The
wiring or connection to the intake lift solenoid should be repaired or replaced
- The ECM connector should be repaired or replaced
Parts
Avatar Canada has in stock the best replacement parts and performance parts for your vehicle. We have parts for all make and model be
it Mazda, BMW, Audi, etc.; and from best brands like Bosch, Denso, Remy and
more. Visit us now!
Easy Diagnosis Of Engine Error OBD Code P0026
- The
electrical connections and wire harness to the bank 1 intake valve solenoid
should be visually checked
- Clear
the code and carefully verify if the code is returning again before you start
performing any further testing
- The test
intake valve control solenoid should be installed for proper diagnosis
- You
must check carefully to see if the valves change during the testing
- The
test solenoid off should be commended and then the intake valves should go to
high lift
- The
later the intake valves should go to low lift
- Now for further diagnosis, you must follow the manufacturer's specific pinpoint tests
Common Mistakes When Diagnosing the P0026 Code
- Just
be sure that first you carefully verify the failure. This can be done by
clearing the code and seeing if the problem is still present
- It is
very important to have special tools like a test solenoid for attempting any
diagnosis
- You
can always follow any pinpoint test done, step by step, so that the failure on
the system gets isolated
- There
is no need to replace any parts unless directed by the pinpoint or visual test