Guide To P2BAB OBD Error Code Solutions

 <<See All OBD Codes

Is your vehicle engine performance decreasing and you notice an increase in the fuel consumption and exhaust emissions? Do you notice the Malfunction Indicator Light illuminated on the dashboard? If there are faults in the exhaust system of the car, especially the NOX sensor, then P2BAB fault code is definitely going to trigger up.

If your diesel-powered vehicle has stored a code P2BAB, it means that the powertrain control module (PCM) has detected incorrect EGR flow in the NOx exceedence.

What causes this problem with the NOx Exceedence Incorrect EGR Flow?

• Damaged/faulty MAF sensor
• Faulty MAP sensor
• Faulty wiring and connectors of the NOx sensors
• NOx sensor heater circuit damaged
• Dirty Air Cleaner
• Defective Electronic Throttle Body
• Obstruction in hose from intake manifold to MAP sensor
• Vacuum leakage in the intake manifold, air induction system, or throttle body
• Damaged/Loose electrical connection related to the sensor and circuit
• Faulty/Damaged or improperly installed Throttle Position Sensor

1. Engine Control Module - ECM faults are rare but can be a big problem as faulty ECM will cause wrong vehicle operations and can also result in wrong OBD codes getting stored in the system which can also cause misdiagnosis. Thus, replace faulty ECM components now!
2. Electronic Control Unit - The ECU coordinates with the temperature sensor to control the blower fan for keeping the battery temperatures under control. So, replace faulty ECU components now!
3. Exhaust Gas Recirculation Valve - Did you just see check engine light flashing on your dashboard? If the computer would detect some faults with the automobile’s EGR valve circuit, then it would set up the check engine light so that the driver is notified about the fault. Don’t waste time and get them replaced or else this fault code can turn up.
4. Fuel Injector - Faulty fuel injector, it will cause rough idles and difficulty in starting. Also, it will affect the fuel economy and engine performance. Fuel injector can also crack or break leading to leakages and should be replaced immediately.
5. Diesel Exhaust Fluid Pump - The diesel exhaust fluid pump needs to work properly if the transmission system has to perform. If it is not functioning, the transmission may slip and cause harsh shifts too. Thus, replace faulty pump now and buy a new one from us!
6. Powertrain Control Module - Check for PCM error which might be due to circuit faults that might require complete replacement and reprogramming. Replace it now!
7. Oxygen Sensor - Inspect for faulty O2 sensor that can affect the engine combustion process and the exhaust emissions. Thus, it is important to understand its importance and replace faulty oxygen sensor now!
8. Manifold Absolute Pressure Sensor - The MAP sensor would fail by getting clogged, contaminated, or sometimes damaged. There can be times when the engine heat would “overcook” the electronics of the MAP sensor and can cause cracks vacuum lines. So, it is very important to take proper care of the MAP sensor and in case you need a new one, then Parts Avatar is here at your service.
9. Diagnostic Tool - In order to detect the error, one needs high grade diagnostic tools. Visit us today to grab amazing deals.

Willing to know some common symptoms of OBD Code P2BAB? Your wish is our demand. Have a look at them below:

Common Symptoms

• Appearance of the service engine soon light
• Sometimes there might be no symptoms at all
• Black smoke emitting from the exhaust pipe during acceleration

We have listed out so ways which would help you to correct the occurrence of OBD Code P2BAB. They are mentioned here as follows:

• Carefully adjust the faults in the NOx sensor heater
• The manifold absolute pressure sensor should be restored to working order
• Recondition the non-functioning ECM
• You must fix the defective EVAP system purge valve
• Make sure to mend the faulty gas cap seal
• It is essential to restore the leaking exhaust system components
• Repair or replace the quirky crankcase ventilation valve and grommet
• Rehabilitate the leaking intake manifold gaskets
• The malfunctioning oxygen sensor should be repaired or replaced as per the need
• It is necessary to perform proper service of the unsound fuel pump
• Adjust the flawed fuel pressure regulator
• The clogged fuel filter should be restored properly
• Tighten the intake manifold bolts

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of NOx Sensor, Diesel Exhaust Fluid, Diesel Particulate Filter, Mass Air Flow Sensor, EGR Valve and many more. Now all your problems would vanish within no time.

If you want to easily diagnose this fault code, then all you have to do is to follow the steps which are mentioned below:

• Check for damaged or broken wirings and connections in relation to the NOx sensors and circuits.
• Check the air cleaner element and look for any signs of clamps or leaking in the pipe starting from the MAF to the Throttle body.
• Then, check the vacuum lines in intake manifold for any cracks, obstructions, or looseness, as these can cause vacuum loss.
• Detach every sensor and check the connector for signs of corrosion and bent pins that are pushed out.
• Inspect for leaky manifold in the intake and clean the carburettor using the carburettor cleaner. The engine RPM will change noticeably after a short shot of the carburettor cleaner over a leak.
• Check for faulty EGR valve and replace it immediately, if found faulty.
• Check the throttle body for signs of coated coke (black greasy substance) and get it cleaned.
• Also check for any faults in the PCM and replace/reprogram it as necessary. Although this problem is rare but if all the other components are fine, then the check is necessary.

Common Mistakes When Diagnosing the P2BAB Code

• Replacing fuel or ignition system parts
• Replacing one or more sensors without testing their functionality prior to the replacement.
• Not checking the wiring and connectors for damages
• Replacing PCM, without checking other components for errors