Guide To P279F OBD Error Code Solutions

<<See All OBD Codes

The trouble code P279F can be defined as Four Wheel Drive (4WD) Range Signal Circuit Low. The four wheel drive (4WD) range signal circuit is being monitored by the transmission control module. This trouble code would be set by the TCM when the four wheel drive (4WD) range signal circuit would not be as per the specifications set by the manufacturer.

The four wheel drive switch would allow the person who is driving the car to shift from 2-wheel drive to 4-wheel Low or 4-wheel high, and it all depends upon the driving conditions. Now if an unusual signal would be sent back by the 4-wheel drive switch, then the P279F error code would start flashing up. The engine control module, powertrain control module or the transmission control module monitors this circuit depending upon the particular automobile.

What causes this problem with the Four Wheel Drive (4WD) Range Signal Circuit Low?

• Malfunctioning four wheel drive range
• Four wheel drive range harness might be open or little
• Substandard electrical connection in the four wheel drive range circuit

1. Engine Control Module - It is not always the components, but the ECM that can also be faulty. It can cause misinterpretation of correct data thus leading to wrong operational decisions which will affect the transmission and overall engine performance. Thus, replace faulty module and reprogram it now!
2. Automatic Transmission Module - If the transmission module is faulty, then the vehicle might experience erratic gear shifts and throttle response. The engine might also stall will accelerating and slowing down. Thus replace faulty automatic transmission module, if required.
3. Powertrain Control Module - Powertrain Control Module can also be faulty in rare cases and thus needs through checks for system and software errors. Thus check and replace it, if required.
4. Electronic Control Unit - The ECU manages the cooling system to control the battery operating temperatures and thus must be replaced if found faulty. Thus, buy new ECU modules and components from us!
5. Diagnostic Tool - Make use of quality diagnostic tools to resolve any OBD error code. Buy quality diagnostic tools from us!

Willing to know some common symptoms of OBD Trouble Code P279F? Your wish is our demand. Have a look at them below:

Common Symptoms

• Visibility in the check engine light
• The 4-wheel drive system might not be working properly

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P279F:

• The malfunctioning ECM should be repaired or replaced as per the need
• The four wheel drive range circuit should be restored to working order
• It is necessary to perform proper service of the unsound four wheel drive range
• Adjust the flawed four wheel drive range harness

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high grade four-wheel drive switch, transfer case, four wheel drive system, transmission control module, four wheel drive system parts, 4 wheel drive system parts, body control module component, electronic control module, transmission shift solenoid, pcm car, ecm car, pcm module, ecm module and a lot more for our precious customers.

If you want to easily diagnose this fault code, then all you have to do is to follow the steps which are mentioned below:

A technician begins by hooking the vehicle to an OBD-II scanner to verify that the code is present, and check for other codes. The freeze frame data along with current data is recorded, and the codes are then cleared to see if they reoccur.

Visual inspection of the wiring and connectors to check for loose connections, corrosion, or shorts is done.

A specialized tool may be used to test the four wheel drive range. Other tests of the four wheel drive range circuit and its components may help pinpoint the problem, as well as inspection of the wiring and connectors.

Disconnect and check the resistance and signal voltage from the fourwheel drive range circuit. If all the components check out, inspect for the fault in the PCM as it can sometimes store wrong OBD code and thus might need replacement or reprogramming.

Common Mistakes When Diagnosing The P279F Code

• Some issues related to the internal transfer case
• Failure in the 4-wheel drive switch
• The transmission control module (TCM) might start failing
• Issues related to the wiring