Guide To P2711 OBD Error Code Solutions

<<See All OBD Codes

A P2711 fault code is stored when the transmission control module (TCM) or powertrain control module (PCM) detects a mismatch in the speed signal between the output shaft and the input shaft. The control module perceives this problem as a mechanical disengagement of the gears, and can result in erratic shifts and drivability issues.

The PCM controls automatic transmission system by using multiple gear ratios and increase the vehicle speed to maximize the engine’s power output. Newer vehicle models are equipped with more than four gear ratios for fuel efficiency. The PCM decides when to shift up or down between gears, based on the vehicle speed vs. throttle position. It does so by using the input coming from various sensors to verify the correct operation of the transmission and all its components. The TCM (transmission control module) calculates gear ratio based on data from the transmission input shaft speed and output shaft speed sensors. The TCM compares the calculated gear ratio to the known gear ratio for each commanded gear. When the output shaft speed sensor reading has malfunctioned, OBD code P2711 gets stored.

What causes this problem with the Unexpected Mechanical Gear Disengagement?

• Insufficient or dirty transmission fluid
• Clogged fluid filter or worn pump
• Solenoid, torque converter clutch or internal blockage
• Internal blockage in transmission main control
• Mechanical failure inside transmission
• Faulty shift wirings or solenoids
• Faulty transmission control module
• Defective torque converter clutch
• Output shaft speed sensor faulty
• Output shaft speed sensor wiring and harness faulty

1. Engine Control Module - If there is any corrosion or breaks in the internal wiring of the harness, then it can cause a short in the ECM or can also cause corrosion in the ECM through the wiring harness. You can always rely on us as we have the best auto parts for our customers.
2. Powertrain Control Module - The onboard computer, or powertrain control module is the brain of the engine control system. Now if the brain is not working properly, then neither is the car engine. Get it replaced before the situation gets worse.
3. Electronic Control Unit - Is your car jump starting on reverse polarity? Or are you facing some intermittent starting issues? If yes, then it indicates that your electronic control unit is bad. So it is very important to replace the defective electronic control unit with us at equitable prices.
4. Diagnostic Tools - Buy quality diagnostic tools to check and diagnose OBD code P2711 error with the help of experienced mechanic. Visit us today!
5. Automatic Transmission Control Module - TCM can be faulty and transmit wrong voltage reading to the PCM thus causing performance issues. Buy and replace new TCM now!
6. Automatic Transmission Sensor - Sensor can also turn faulty but to mechanical failures that will affect the voltage signal being sent to the PCM/TCM. Thus, replace faulty sensor immediately.
7. Transmission Fluid Pump - Harsh shifts and audible transmission noise are the major symptoms of faulty fluid pump. This leads to decreased performance and chances of increased physical damages to the transmission components. Thus, replace faulty pump now!
8. Transmission Fluid Pump Harness - Damaged pump harness can lead to problematic transmission performance and can cause transmission slipping, rough shifts, fuel leakages and delayed engagements. Buy new fluid pump harness now!
9. Auto Transmission Shift Solenoid - If your automatic transmission is performing erratically, it could be a sign your transmission’s solenoids are failing or have failed. Thus, replace it now!
10. Speed Sensor - The output shaft speed sensor is responsible for helping the transmission system take important decisions regarding accurate gear ratios. Thus, replace the faulty sensor now!
11. Gear Shaft Seal Kit - The gear shaft may be loose or the sealant may wear out over time. Thus, repair the loosened gear shaft seals immediately and buy a new seal kit now!

After knowing all the cause behind the issues, let’s have a look at a few common symptoms of this problem. Read through this section to learn more about this error code P2711.

Common Symptoms

• Delayed shifting or vehicle not shifting into the right gear
• Transmission slipping
• Decrease in fuel efficiency
• Speedometer not running
• Check Engine Light illumination
• Engine stalling and misfiring

Fixing problems with your car is not as easy as it might seem. You need to be extremely careful and follow certain steps.

• Repair or replace any corroded or damaged wires in and around the transmission control module
• Replace transmission fluid and wiring, if not in working condition
• Repair or replace problem with the pump, shift solenoids, or torque converter

If you need parts to correct this problem, you can easily find them all with us at PartsAvatar. We have in stock high end auto parts from top automotive brands. So what are you waiting for? Grab best deals today with us.

If you want to easily diagnose this fault code P2711, then all you have to do is to follow the steps which are mentioned below:

• A suitable OBD-II scanner (or code reader) and a digital volt/ohmmeter will be most helpful in trying to perform a successful diagnosis.
• Begin with a visual inspection of all wiring and connectors. Repair or replace damaged, disconnected, shorted, or corroded wiring, connectors, and components as necessary.
• An experienced technician with a specialized scanner may determine the general area of the malfunction much more rapidly and easily than someone using a code reader and a digital volt ohmmeter.
• Check the fluid in the transmission should be checked for quality, and the level of fluid prior to further diagnostic tests. Replace old or dirty fluid as required.
• Perform a torque converter stall speed test to determine if the engine stall speed is within factory specifications. The engine speed must match the readings from the transmission sensor.
• Faulty TCM (Transmission Control Module) and PCM should also be repaired, reprogrammed or replaced as required.

Common Mistakes When Diagnosing the P2711 Code

Some of the common mistakes done while changing diagnosing the OBD code P2711 are:

• Improper check for transmission fluid and solenoids
• Simply replacing the Powertrain Control Module (PCM) or Transmission Control Module without considering other possibilities of problem
• Not noticing the damaged or loosened wiring and circuit problems