P2619 OBD Error Code: Problem & Solutions

<<See All OBD Codes

If you feel a sudden drop in the engine performance and continuous stalling and hard idles along with flashing of check engine lights on the dashboard, this may be an indication of OBD Code P2619 being stored in the PCM/ECM.OBD code P2619 means Crankshaft Position Signal Output Circuit High Issue.

The crankshaft position sensor is an engine management component found on virtually all modern vehicles with internal combustion engines. The Crankshaft sensor monitors the position and rotational speed of the crankshaft and sends the information to the engine control unit in order to make appropriate adjustments based on operating conditions. The crankshaft speed and position are most important parameters used in engine management calculations, and many engines cannot run if the crankshaft position sensor is not providing an accurate signal.

OBD code P2619 gets stored in the PCM when it finds that the crankshaft sensor has a higher output voltage than usual.

What causes this problem with the Crankshaft Position Signal Output Circuit High?

• Failed crankshaft position sensor
• Short/open wiring problem
• High voltage and poor electrical connections
• ECU (Engine Control Unit) error

1. Engine Control Module - Want to know the most common reason behind the failure in the engine control module? Corrosion or damage because of moisture can cause ECM failure. Corrosion might enter the ECM through the wiring harness and moisture can enter by a failure in the seals in the ECM itself.
2. Engine Wiring Harness - Your car ECM would not operate properly if there are some cracks or break in the engine wiring harness. Corrosion as well as physical damage are the most common reasons why you should replace an engine wiring harness. Purchase high grade engine wiring harness online from Parts Avatar Canada.
3. Powertrain Control Module - The PCM makes the engine and transmission work in tandem. Any issue with the powertrain control module will cause major problems with the efficient running of the vehicle.
4. Fuel Injector – The fuel injectors are an important component of the fuel delivery system that helps in proper utilization of the fuel entering the engine. This not only helps in taking care of the air to fuel ratio in the engine, helping the combustion process but also enhances the performance. Thus, replace faulty injector now!
5. Electronic Control Unit - If your vehicle fails to start for no apparent reason, this is also a good indicator that there can be some issues with the ECU. If you check the car battery, starter and other common electrical components, and the vehicle still does not start, a quirky electronic control unit should be the next logical thing to consider.
6. Diagnostic Tool - In order to fix these errors, you need a few diagnostic tools to get your car problems pointed out easily. Our diagnostic tools collection will come in handy to do so and resolve all your vehicle problems. Visit today!
7. Crankshaft Position Sensor – The main symptom associated with a bad or failing crankshaft position sensor is difficulty in starting the vehicle. The crankshaft position sensor is used to monitor the speed and position of the crankshaft and other aspects that play an important role when starting the engine. If the crankshaft position sensor is faulty, the vehicle may have starting issues or not start at all.

If you are facing OBD error code P2619, then there are significant common symptoms that can be felt or observed. We have worked out a list here to help you out in understanding this problem better.

Common Symptoms

• Issues in starting the vehicle
• Intermittent stalling
• Check engine light comes on
• Uneven acceleration
• Engine misfires or vibrates
• Rough engine idles
• Reduced fuel economy

It is very important to fix the fault code P2619. So here are some ways with which you can correct this issue:

• Replace faulty crankshaft position sensor
• Repair/replace open or short in the wiring and connections
• Replacement of PCM/ECM

However, if you face any issue then we` have stocked a wide range of best priced Pcm, Crankshaft Position Sensor, Crankshaft, Crank Sensor, Ecm, Digital Volt, Ohmmeter, Throttle Position, Electronic Pressure Regulator, Timing Belt, Timing Chain and more to help you out in fixing your car.

If you want to easily diagnose this fault code P2619, then all you have to do is to follow the steps which are mentioned below:

• Install a scan tool in vehicles OBD-II port to check if P2619 is present or not.
• Freeze frame data and test drive to check if the code reappears under same conditions.
• If you find that the Check Engine Light has returned upon test, then OBD code P2619 exists.
• Always refer to the technical service bulletins (TSB) for your particular make and model in vehicle information source. If you find one that matches the symptoms and code/s presented by the vehicle in question, it will very likely aid you in your diagnosis. TSB listings are compiled from thousands of successful repairs.
• Perform a visual inspection of wiring and circuit for any damage, breaks, or shorted wiring in the crankshaft system.
• Using the OBD scanner, analyse the engine crank and RPM. This reading usually falls between 100 and 500 RPM. If the reading variates, it indicates that the crankshaft sensor isn't working right and might need replacement. If the scanner reading is zero, it indicates that the crankshaft sensor has failed completely.
• Next, test the sensor for it resistance output. Attach one end of the multimeter to each wiring lead of the sensor. There is a short circuit, if the resistance is found to be zero. Similarly, if the resistance is infinite, it means that there is an open circuit in the sensor. Match it against the manufacturer's specifications for any other reading. If your reading is not close to the recommended resistance, then the sensor needs replacement.
• Test the crankshaft sensor by checking the output voltage using a multimeter with the engine cranking. This voltage reading is usually around 200 millivolts, but this can vary from vehicle to vehicle. Always check for the manufacturer's specifications to see the variations.

Common Mistakes When Diagnosing the P2619 Code

P2619 is an uncommon code and following all diagnostic steps is important so nothing is overlooked. Crankshaft position sensors should be properly examined and replaced if faulty.