Guide To P2607 OBD Error Code Solutions

<<See All OBD Codes

The trouble code P2607 can be described as Intake Air Heater “B” Circuit Low. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. This would also give rise to the illumination of the check engine light.

The P2607 fault code is a generic powertrain code which is associated with the issues in the computer circuit output. This error code would start appearing when your vehicle’s engine control module (ECM) would receive a notification that the second intake air heater (heater B or 2) is presenting a low voltage reading or is exceeding the specifications set by the manufacturer.

What causes this problem with the Intake Air Heater “B” Circuit Low?

• There can be inoperative heater element relay
• Unusable heater element
• Quirks in the temperature sensor
• Defective intake air heater blower
• Malfunctioning or restricted air duct
• Blower motor might be flawed
• Imperfect PCM

1. Intake Manifold - An intake manifold is a component that delivers either air or an air/fuel mixture to the cylinders. The design of these components varies widely from one application to another, but they all perform the same basic function and they all have a single input and multiple outputs. In carbureted engines, the intake manifold connects the carburettor to the intake ports. In fuel-injected engines, the intake manifold connects the throttle body to the intake ports. Replace affected intake manifold now!
2. Electronic Control Unit – ECU monitors the temperature differences in the boost converter with the help of the temperature sensors to prevent the converter from overheating and malfunctioning. Thus, replace faulty ECU immediately.
3. Engine Control Module - ECM failures and faults can be very difficult to find and resolve as these are very rare and might require a complete reprogramming of the system to avoid wrong codes from getting stored in the system, leading to misdiagnosis. Replace it now!
4. Intake Valve – A potential issue with the intake valve is engine performance issues. If the intake valve has an issue it can cause the vehicle to experience engine performance issues such as misfires, a decrease in power and acceleration, a decrease in fuel efficiency, and even stalling. Thus, replace damaged valve now!
5. Powertrain Control Module - Faulty PCM can disrupt the normal functioning of the vehicle by affecting the transmission system and the fuel delivery system. This will cause the system to store wrong OBD error and thus can lead to misdiagnosis.
6. Diagnostic Tool - In order to be that DIY guy, you need few diagnostic tools to get your car problems pointed out easily. Our diagnostic tools collection will come in handy to do so, so why not have a look?

We care for our customers and that’s why we can totally understand your problem. That’s the reason why we have listed out some major symptoms behind the flashing up of OBD Code P2607. They are mentioned here as follows:

Common Symptoms

• Check engine light can start flashing up
• Engine may not start at all
• There might be longer than normal cranking time
• Rough idle during cold temperatures
• Engine hampering

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P2607:

• You must fix the defective battery cable
• Make sure to mend the faulty ECM/PCM
• It is essential to restore the flawed wires
• Repair or replace the quirky loose connections in the battery wires
• Rehabilitate the defaults in the air intake heater B (or number 2) relay
• The malfunctioning air intake heater ground should be repaired or replaced as per the need
• Carefully adjust the faults in the electrical connectors or bent pins
• The heater element should be restored to working order
• Recondition the non-functioning grounded wires
• It is necessary to perform proper service of the unsound intake air heater B
• Adjust the flawed temperature sensors

Now are you thinking that from where will you purchase these car parts? You have arrived at the right place. We at Parts Avatar care for our customers, that’s why we provide the best quality of intake air heater, intake air heater blower, heater element relay, air duct, blower motor, powertrain control module, digital voltmeter, intake air temperature sensor, intake air heater relay, body control module, pcm, ecm at marketable prices.

Do you wish to diagnose P2607 error code easily? Here are some steps which you should follow in order to diagnose this fault code:

Obtain your vehicle specific Technical Service Bulletins (TSB) and see if you can find the code and ways to resolve it there. The TSB will be source of reference through the diagnostic procedure. Make sure you match the TSB’s accurately with your vehicles, year, make, model and engine details.

The intake air heating circuit may not work automatically if the ambient air or engine temperature is above the limit which is set by the manufacturer. The circuit should activate if it is commanded "ON" with a scanner, or if power is applied manually.

• Inspect the heater element, is it turning "ON" NOTE: Do not touch element or heat shield 
• Make sure to examine the blower motor, is it turning "ON"
• The circuit connections and wiring for obvious defects should be visually inspected
• It is essential to visually inspect the condition of the air ducts for obvious defects
• Examine electrical connections for security and corrosion

Advanced Steps

• The advanced steps become very vehicle specific and need the appropriate advanced equipment to perform in the right way.
• There would be a need of a digital multimeter and the specific technical references to carry out this procedure.
• Voltage requirements will vary depending upon the specific year, make and model of the vehicle.

Specific Checks:

• Specific checks should be performed by utilizing the troubleshooting guidelines for the particular vehicle using the technical manual or online reference material.
• These steps will guide you through the process of inspecting the power and ground to each component within the intake air heater circuit in the proper sequence.
• If the voltage is right to a component that is not functioning, then it would mean that the part is most likely faulty and it should be restored.
• If power is not available to operate the circuit, continuity checks would be required to identify defective wiring or components.

Common Mistakes When Diagnosing The P2607 Code

• There are a lot of mechanics who would simply rush into the judgement that the intake air heater is faulty, but they should keep in mind that the repair might have a temporary effect, but then this error code would return again. It is essential to test each and every possibility for why the component is not working properly to make sure it is fixed properly the first time.