Guide To P2603 OBD Error Code Solutions

<<See All OBD Codes

The trouble code P2603 can be elucidated as Coolant Pump "A" Control Circuit High. The coolant pump "A" control circuit is being monitored by the engine control module. This trouble code would be set by the ECM when the coolant pump "A" control circuit would not be as per the specifications set by the manufacturer

This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present.The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another. The coolant pump A (CP-A) is can generally be located mounted to the front of the engine, on top of the car engine, inside the wheel wells or sometimes even against the bulkhead. The CP-A would be operated by an electrical signal which would come from the powertrain control module.

What causes this problem with the Coolant Pump "A"Control Circuit High?

• Malfunctioning coolant pump
• Coolant pump harness might be unlocked
• Coolant pump circuit might have bad electrical connection
• Unusable powertrain control module

1. Automatic Transmission Module - Faulty transmission module can cause problematic down shifts and upshifts, leading to stalling while accelerating or slowing down. This can also hamper many transmission system parts. Thus replace it now!
2. Engine Control Module - Dead cells in batteries can cause a failure in the engine control module. Many times a battery is left in the rig long after a cell has died. This would affect the grounding in the car battery.
3. Fuel Injector - Faulty fuel injector, it will cause rough idles and difficulty in starting. Also, it will affect the fuel economy and engine performance. Fuel injector can also crack or break leading to leakages and should be replaced immediately.
4. Powertrain Control Module - If there are some faults in the PCM, then it may throw off the timing and fuel settings of the engine, which can negatively affect the performance. A flawed PCM may cause the vehicle to experience a reduction in fuel efficiency, power as well as acceleration.
5. Electronic Control Unit - Do you know that the poor performance or unexplained drops in fuel economy or efficiency are often associated to onboard car computer problems, or defective ECU issues?
6. Diagnostic Tools - Use factory grade diagnostic tools to resolve OBD code P2603 error. Buy new diagnostic tools and equipment for us.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Visibility in the check engine light
• Sometimes there might be a lot of heat
• A/C system not operate properly

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• It is essential to restore the flawed loose or broken ground wires
• The malfunctioning CAN bus should be repaired or replaced as per the need
• Carefully adjust the faults in the wiring or connectors for the CAN bus harness

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of hybrid battery, coolant pump, hybrid powertrain control module, pcm module, ecm module, pcm, ecm and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

After verifying the P2603 code with an OBD-II scanner, the mechanic should begin with a visual inspection of all electrical components, especially looking for some issues in the wiring and circuits before testing the CAN bus and its harness. Any issues should be repaired, and the code should be cleared from the system. If the code reappears after a retest, the mechanic should then move on to performing voltage tests and resistance tests on the sensor, and comparing the information to the manufacturer’s specifications. If the readings are within the correct limits, then the sensor needs to be replaced. However, if the readings are not within the correct limits, then the issue lies elsewhere. The mechanic should continue checking each possible cause, clearing the code and retesting the system after each attempt, to be sure that the correct solution is found.

Common Mistakes When Diagnosing The P2603 Code

• Common mistakes while diagnosing this trouble code are unnecessary and expensive replacements which usually happens when one doesn't follow all the steps carefully.
• The most common mistake while diagnosing this code is missing out on diagnosing steps which further leads to the expensive and unnecessary replacements. It is always recommended to seek the help of experienced diagnostician to avoid any mistakes.