P240B OBD Error Code: Problem & Solutions

<<See All OBD Codes

If you notice Check Engine Light illumination on the dashboard along with reduced fuel efficiency on rare cases, it may be due to problems with the Evaporative Emission Control System leading to OBD code P240B getting stored in the PCM (Powertrain Control Module).

OBD code P240B indicates a change of value in the lead detection pump that is outside the specifications set by the manufacturer, during the operation of the vehicle or EVAP monitor test.

The EVAP system uses a venter reservoir called ‘canister’, which stores excessive fuel vapours until the engine is being run under the right conditions to burn them properly. This reservoir keeps the fuel vapours from escaping to the atmosphere.

When the fuel is stored, a fuel vapour pressure is created, acting as a propellant, causing the vapour to go through the network of rubber hoses and metal tubes, and will reach the canister. These fuel vapours from the tank storage are then discharged through the pressure relief valve located at the top on top of the fuel tank, which is then forced through a complex web of rubber lines and metal connectors to the charcoal canister, where they will accumulate. The canister contains a charcoal element that absorbs fuel vapours, storing them for release at the right time.

The purge control valve/solenoid regulates the intake vacuum to the EVAP canister and draw fuel vapour to the engine when the condition is ideal for the fuel to be burned, rather than releasing them to the atmosphere. The PCM controls the purge control valve/solenoid, which is the heart of the EVAP system.

What causes this problem with the Evaporative Emission System Leak Detection Pump Heater Control Circuit Low?

• Failed or faulty EVAP leak detection pump
• Missing or loose fuel cap
• Broken, burned, or collapsed canister valve
• Leak detection pump circuit wiring defective
• Faulty Powertrain Control Module

1. Engine Control Module - If there is any corrosion or breaks in the internal wiring of the harness, then it can cause a short in the ECM or can also cause corrosion in the ECM through the wiring harness. You can always rely on us as we have best auto parts for our customers.
2. Powertrain Control Module - The onboard computer, or powertrain control module is the brain of the engine control system. Now if the brain is not working properly, then neither is the car engine. Get it replaced before the situation gets worse.
3. Electronic Control Unit - Is your car jump starting on reverse polarity? Or are you facing some intermittent starting issues? If yes, then it indicates that your electronic control unit is bad. So it is very important to replace the defective electronic control unit with us at equitable prices.
4. Diagnostic Tools - Buy quality diagnostic tools to check and diagnose OBD code P240B error with the help of experienced mechanic. Visit us today!
5. EVAP Leak Detection Pump - The main purpose of the LDP (Leak Detection Pump) is to pressurize the fuel system for leak checking. It closes the EVAP system vent to atmospheric pressure so the system can be pressurized for leak testing.
6. Vapor Canister Valve - In modern cars, the purge valve is an electrically-operated solenoid that is controlled by the engine computer. When the engine is off, the purge valve is closed. When the engine is running and fully warmed up, the engine computer gradually opens the purge valve to allow some amount of fuel vapors to be moved from the charcoal canister and burned in the engine. The purge flow is monitored by a number of sensors. If the purge flow is less or more than is expected under the conditions, the computer illuminates the "Check Engine" light.
7. Vapor Canister Purge Solenoid - The canister purge solenoid is the component in the EVAP system that is responsible for “purging” the EVAP system, by acting as the switch that allows the vapor into the engine. When the purge solenoid fails, it will cause problems for the EVAP system, which will affect the vehicle’s emissions output levels.

Willing to know some common symptoms of OBD Code P240B? Your wish is our demand. Have a look at them below:

Common Symptoms

• Check Engine Light on
• Reduced fuel economy
• Fuel odour in rare cases due to vapour release

We have listed out some ways which would help you to correct the occurrence of OBD Code P240B. They are mentioned here as follows:

• EVAP leak detection pump replacement
• Replacement of defective or damaged wiring or connectors in the LDP circuit
• Replacement of canister vent valve
• Replacement or reprogramming of PCM

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of ECM, PCM, EVAP and many more. Now all your problems would vanish within no time.

If you want to easily diagnose this fault code P240B, then all you have to do is to follow the steps which are mentioned below:

• Get proper access to the system by removing the fuel tank. Then loose, broken, or damaged wires and electrical connectors must be repaired.
• Check the lines for any cracks or holes. If everything seems to be okay after a visual inspection, then simply replacing the sensor can resolve the problem.
• Also inspect for EVAP leak detection pump and if it looks good, then simply unplug all related controllers, and retest individual circuits using the DVOM. Replace open or shorted circuits as needed.
• In many cases, the components of EVAP emission control system are needlessly replaced when there is a vacuum leak present, or the fuel cap is simply not properly tightened. Thus, it is important to conduct a thorough diagnosis to make sure you don’t waste money on replacing fully-functional components.

Common Mistakes When Diagnosing the P240B Code

• The most common mistake associated with a P240B code is not properly inspecting all components, wiring, and connectors before replacing any part of the evaporative emission control system. For example, in some cases, a vacuum leak could be due to a loose or damaged fuel cap, not a faulty vacuum hose.
• Thus, it is important to carefully inspect all the components in question and thus need to follow proper quality and operational check also.