Guide To P2307 OBD Error Code Solutions
OBD Code P2307 - Ignition Coil "C" Primary Control Circuit High
The trouble code P2307 can be described as Ignition Coil "C" Primary Control Circuit High. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. This would also give rise to the illumination of the check engine light.
Learn More About OBD Error Code P2307
The majority of OBD-II
equipped automobiles use a “coil on plug” system to provide ignition spark. The
PCM would continuously monitor the ignition system. The P2307 error code would
be set when the PCM would detect some issues with the voltage in the circuit.
What causes this problem
with the Ignition Coil "C" Primary Control Circuit High?
- There can be distorted Ignition Coil 'C'
- Ignition Coil 'C' harness is open or small
- Ignition Coil 'C' circuit might have inadequate electrical
connection
- Malfunctioning relay or blown fuse
- Faulty PCM
- There can be inoperative camshaft or crankshaft sensor
- The wiring might be flawed
Replace/Repair These Parts To Fix Code P2307
- Electronic Control
Unit - ECU monitors
the temperature differences in the boost converter with the help of the
temperature sensors to prevent the converter from overheating and
malfunctioning. Thus, replace faulty ECU immediately.
- Ignition Coil
- Is your check engine light appearing on your dash? It is an indication
that there are some defaults in your ignition coil. Don’t waste time and get
them replaced or else this error code can turn up.
- Fuel Tank Pressure
Sensor - The fuel
tank pressure sensor helps in many ways, most importantly by saving fuel,
minimizing environmental pollution, and preventing damage to the engine. The
pressure sensor, which is normally positioned inside or on top of the tank,
works to detect the pressure in the fuel system, with the end goal of
identifying leaks and defective gas caps. Thus, replace faulty sensor now!
- Engine Control
Module - ECM failures
and faults can be very difficult to find and resolve as these are very rare and
might require a complete reprogramming of the system to avoid wrong codes from
getting stored in the system, leading to misdiagnosis. Replace it now!
- Powertrain Control
Module - Faulty PCM
can disrupt the normal functioning of the vehicle by affecting the transmission
system and the fuel delivery system. This will cause the system to store wrong
OBD error and thus can lead to misdiagnosis.
- Diagnostic Tool
- In order to be that DIY guy,
you need few diagnostic tools to get your car problems pointed out easily. Our
diagnostic tools collection will come handy to do so, so why not have a look?
Symptoms Of The OBD Error Code P2307
We care for our customers and that’s why we can totally understand your problem. That’s the reason why we have listed out some major symptoms behind the flashing up of OBD Code P2307. They are mentioned here as follows:
Common Symptoms
- Visibility in the check engine light
- The performance of the engine might not be good
- Issues related to diminishing fuel economy
- Other codes might also appear
How To Correct P2307 Ignition Coil "C" Primary Control Circuit High
If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P2307:
- Rehabilitate the defaults in the spark plug
- The malfunctioning wiring should be repaired or replaced as per the need
- Carefully adjust the faults in the PCM
- The ignition coil connector should be restored to working order
- Make sure to mend the faulty camshaft or crankshaft sensor
- Repair or replace the quirky engine parts
- Recondition the non-functioning ignition coil
- It is necessary to perform proper service of the unsound ignition coil wiring
- Adjust the flawed fuel injector
Now are you thinking that from where will you purchase these car parts? You have arrived at the right place. We at Parts Avatar care for our customers, that’s why we provide best quality of ignition coil, circuit wires, ignition coil connectors, spark plug, powertrain control module, engine control module, pcm car, ecm car, body control module component, ecu car, transmission shift solenoid, ignition system parts, pcm module, ecm module at marketable prices.
Easy Diagnosis Of Engine Error OBD Code P2307
Do you wish to diagnose P2307 error code easily? Here are some steps which you should follow in order to diagnose this fault code:
The mechanic or the technician will use a diagnostic scanner or code reader like DVOM to visually scan for the error codes in the vehicle. Use the vehicle information source to search for applicable technical service bulletins (TSB). If you locate a TSB that matches the vehicle make and model, symptoms exhibited, and the code stored, it will help you to arrive at a diagnosis. You may also need to obtain diagnostic flow charts, wiring diagrams, connector face views, connector pin out charts, component locations, and component testing procedures/specifications from the vehicle information source. All this information will be needed to correctly diagnose the stored code P2307. After that test drive the vehicle to see if the code P2307 is reset. Drive until one of two things happens: Either the PCM enters readiness mode or the code is reset. If the code is reset, continue with the diagnosis. If it is not, you are dealing with an intermittent condition which may have to worsen before an accurate diagnosis may be achieved. Now if the code has been restored, then you must continue with the diagnosis. One should obtain connector face views, connector pin out charts, component locator charts, wiring diagrams, and diagnostic flow charts by utilizing your source of vehicle information. A visual inspection of associated wiring and connectors should be performed. Make sure to repair or restore the wiring that has been cut, burned, or flawed. Wiring on top of the engine is often defective due to wildlife attempting to stay warm in cold climates. The DVOM should be used to inspect the voltage and ground circuits at the ignition coil. If no voltage has been detected, then you should check the system relay and associated fuses. Restore the faulty relays or blown fuses as per the requirement. If voltage and ground have been detected at the coil, examine the corresponding ground circuit at the PCM connector with the engine running. If ground pulse is detected there, then there is an open circuit between the coil as well as the PCM. If no ground pulse is discovered there, then there is some fault in the PCM or there might be PCM programming error.
Common Mistakes When Diagnosing The P2307 Code
- A big mistake which is made by a lot of technicians is that they assume that this fault code is appearing because of faulty ignition coils and spark plugs, when in reality the actual reason is defective wiring and connectors.