P2167 - OBD Trouble Code

<<See All OBD Codes

Error code P2167? Wondering on how to solve it? Parts Avatar is here for you! Here’s all that you need to know about the error code P2167. This OBD-II code P2167 is generally referred to as a throttle/pedal position sensor "E" maximum stop performance. The pedal position sensor/switch is an element of the accelerator pedal assembly, while the throttle position sensor/switch is situated on the throttle body of the intake manifold. These sensors installed inform the engine control module (ECM) about the speed required by the driver as well as it updates on how to speed up too. Whensoever the PCM identifies an error in this sensor or its circuit, the code P2167 is stored. The speed of the vehicle may also be restricted by the PCM to 20 miles per hour or less ("limp home mode") to protect the engine and the driver. It happens so because of the control module’ inability to precisely notify the engine performance being requested.

This code P2167 is a mainstream OBD-II diagnostic trouble code (DTC) that signals an error with the throttle / pedal position sensor E maximum stop performance. It can be viewed with other throttle body and pedal position sensor codes as well. The signals from the throttle position sensor and the pedal position sensor are used by the electronic throttle body to determine how far to open the throttle plate allowing air into the engine. The check engine light is illuminated and the maximum stop performance fault with the sensor E is detected by the electronic control unit (ECU). The failsafe mode is set and the check engine light can be observed on the dashboard. The code P2167 tends to stay until a normal operation is observed or the code is totally resolved

What causes this problem with the Throttle/Pedal Position Sensor E Maximum Stop Performance?

• A damaged throttle position sensor
• A malfunctioning throttle position actuator
• A faulty throttle actuator control motor
• Unsound electrical components in the system often in the throttle actuator motor
• Distorted ground wire
• Disconnected or open control module ground strap
• A damaged PCM

1. Powertrain Control Module - Error code P2167 flashing? Tensed? But don’t know the reason behind all these complications? A damaged powertrain control module leads to downward emissions along with other issues like a sluggish engine crank, failure in the emission system etc. We advise you to get your faulty PCM changed now by simply logging into Parts Avatar.
2. Throttle Position Sensor - Signals from the throttle position sensor measures and combines many times per second with other data such as air temperature, engine RPM, air mass flow, and decides how quickly the throttle position has to change. So we advise you to change your defective throttle position sensor as soon as possible in order to get rid of a whole lot of problems as well as the error code P2167.
3. Throttle Position Switch - Don’t know the reason behind this sudden engine stalling without any apparent reason? It could have happened due to a faulty throttle position switch. It is advised to get it changed or repaired as soon as possible. Tune into Parts Avatar now!
4. Throttle Body - Having problems with the throttle? It should be noted that a damaged one makes the sensor prone to malfunctions. Repair or replace now. Don’t you worry, Parts Avatar has it all. All you need to do is to simply click and tune into our website.
5. Intake Manifold - Observing a sudden overheating in the engine? Well, it likely be due to a defective intake manifold. To further avoid such problems and the error code P2167, we strongly advise to change this faulty unit immediately.
6. Engine Control Module - Often regarded as the backbone of the system, this essential unit if malfunctioning should be changed right away in order to avoid complications throughout the system. Tune into Parts Avatar now!
7. Pedal Position Sensor - When the pedal position sensor is not working efficiently, a lot of issues arise like a poor fuel economy and an inconsistent engine throttle. Repair or replace it now if you want to get rid of the problems caused by the error code P2167.
8. Pedal Position Switch - A distorted pedal position switch can end up being the chief host inviting the error code P2167 and is likely to trigger problems with the APP sensor. So replacing one can be one of the wisest decisions to avoid a problematic system.
9. Electrical Connectors - Short circuited or loose electrical connectors also cause a corrosion in the battery. Not replacing one in right time can cost you not only a lot your money but also time. Repair or replace it now frome Parts Avatar.
10. Dbw Actuator Motor - Throttle hesitation, engine stalling and an illuminated check engine light is what you’ll probably experience after a DBW actuator motor is damaged. Log into Parts Avatar for supreme quality parts.
11. Automatic Transmission Parts - The automatic transmission parts constitute an essential unit in the system. Inferior quality or damaged ones are dangerous both for the driver as well as the system. Mend or restore now. What are you waiting for?
12. Fuel Shutoff Valve - Vacuum leaks? It is triggered due to a malfunctioning fuel shutoff valve. Restore or repair now! In order to get yours right at your doorstep, tune into Parts Avatar now.
13. Digital Voltmeter - Battery dead? Alarmed? For your information, it is likely caused due to a faulty digital voltmeter. Now get your error code P2167 fixed and vehicle started with Parts Avatar. Log in now!
14. Ohmmeter - Fearing the error code P2167? An inferior quality ohmmeter can always be hazardous for the system also it is one of the primal causes behind the occurring of the error code P2167. Tune into Parts Avatar for supreme quality ohmmeter at economical prices.
15. Throttle Actuator Motor - Trouble code P2167 Well, a lot of problems are likely to accompany a damaged throttle actuator motor including no acceleration, lack of power and a rough idle. Tune into Parts Avatar if you are planning to get your throttle actuator motor repaired or replaced.
16. Accelerator Pedal Position Assembly - Love travelling but hate halts? Alarmed? Not only this but a whole lot of problems including issues with the throttle body and throttle pressure are likely to follow a malfunction in the accelerator pedal position assembly. Mend or restore it now!

We at Parts Avatar Canada care for our customers, and that’s why we will help you to diagnose P2167 code by listing out some major symptoms. They are mentioned below as follows

Common Symptoms

• An illuminated check engine light visible on the dashboard
• Engine glitches
• No start condition
• Engine stalls
• Zero or bad acceleration

Learn the ways with which you can correct this trouble code:

• Replace or repair the damaged electronic throttle body
• Repairing or replacing the loose or corroded wiring harness
• Change or restore the throttle position sensor
• Replace or restore the pedal position sensor
• Fix the damaged or burnt electrical connections

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of PCM, throttle position sensor, throttle position switch, throttle body, intake manifold, accelerator pedal assembly, engine control module, pedal position sensor, pedal position switch, electrical connectors, Dbw actuator motor, connectors, automatic transmission, fuel shutoff valve, digital volt, ohmmeter, throttle actuator motor, accelerator pedal position assembly and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P2167 code to be stored:

• Firstly, a scan tool should be used to check for any codes stored in the ECU. at times, there is a possibility of finding pending and history codes
• It is advised that of all codes present should be registered along with the freeze frame data for the conditions under which the code was stored
• For a fresh start, all the codes should be cleared
• The vehicle should be taken for a test drive (only if it is safe to be driven). It should be performed under same conditions as the freeze frame data
• A visual inspection should be performed for any traces of damage or part failure. Mechanics should also search for worn or damaged wiring
• A multimeter should be used to check for the correct voltage present at the throttle position sensor along with the pedal position sensor
• If you find the correct voltage, then the air intake should be removed. Then the mechanic should inspect the electronic throttle body for any traces of damage and the ability to function.

Common Mistakes When Diagnosing the P2167 Code

Here we have listed a few common mistakes that should be avoided while performing the diagnosis:

One is likely to fail while performing the diagnosis if mistakes are performed. It is important to perform a step-by-step diagnosis. It is essential to critically inspect the entire system and not miss general causes. For the manufacturer it is easy to restore the electronic throttle body as a whole only to find a wiring issue was the only cause.