Error Code P210E: What It Means & What To Do?

<<See All OBD Codes

See the error code P210E? Don’t know how to comprehend it? Well, you have arrived at the right place. Parts Avatar has listed for you everything you need to know about this error code P210E. This generic OBD-II code decreased engine performance is mostly determined as the throttle/pedal pos sensor C/F voltage correlation. Also, the opening of the throttle valve is monitored by the electronic throttle control system (ETCS). It can be observed that at the time when the driver presses the accelerator pedal, a signal is transmitted by the accelerator pedal position sensor (APP) to the engine's control module (PCM) notifying the PCM about the power that has been requested by the drive from the engine. Then accordingly the PCM orders the throttle plate to open. In cases where the PCM detects a improper opening of the throttle (through a signal received for the APP sensor) the code P210E is stored. The PCM also puts the engine into the "limp home mode" thus restricting the power available from the engine to avoid unwanted acceleration.

It should be noted that the correlation of both the voltages is controlled by the computer. When the voltages collate, the system functions correctly. On the other hand, when both the voltages fail to match for two seconds the code P210E is set. The code P210E when stored signals at an error somewhere throughout the system. Also, this code P210E also leads to additional codes being stored as well. In conclusion, one should note that it is a dangerous situation when the control over throttle is lost.

What causes this problem with the Throttle/Pedal Pos Sensor C/F Voltage Correlation?

• The wiring connector or “pig tail” on the throttle body can trigger problems like a weak electrical connection. Also, the female terminals on the pigtail often burn or pull out the connector
• A loose wire on the pigtail shorting to ground.
• A damaged top cover of the throttle body (preventing the gears from turning correctly).
• A distorted electronic throttle body
• A failure in the accelerator pedal sensor or its wiring
• The engine management computer is damaged
• The TPS sensors failing to parallel for a few seconds, also the computer needs to be turned again through its relearn phase to repair active response to the throttle body.
• The computer might also need a reprogramming

1. Throttle Position Sensor - Love travelling but hate these halts? Well, a damaged throttle position apart from triggering the error code invites other problems like no acceleration, a difficulty in the engine smooth idle and a poor fuel economy. Change your old throttle position sensor from Parts Avatar now!
2. Electronic Throttle Control System (ETCS) - Do you have problems with the electronic throttle control system? Don’t you worry, Parts Avatar has it all. A faulty ETCS could end up being the root cause behind the error code P210E. Not only this, problems with the engine are likely to follow as soon as the electronic throttle control system has been diagnosed as faulty. Amendments should be performed immediately.
3. Accelerator Pedal Position Sensor (APP) - It should be noted that whenever the APP sensor is not functioning correctly, it will also lead to problems with fuel efficiency. The APP sensor other than monitoring and applying throttle pressure to the throttle body, also helps stabilize throttle control. So we advise you to get your APP sensor change or replaced right away to avoid major expensive repairs in future. Tune into Parts Avatar now!
4. Powertrain Control Module - Well, a failure in the powertrain control module makes the system prone to many issues including a poorly running system, significant increase in the carbon emissions, stuttering, stalling or choking of the engine. It is recommended that the defective pcm should be replaced before it can cause any further damage to the system.
5. Throttle Plate - Get your error code P210E fixed instantly with a new throttle plate if you wish to combat electrical problems, low or high idle issues and dirt/carbon deposits around the housing. Parts Avatar is just right place that provides the best throttle plates across the country.
6. Electronic Throttle Body - A jammed or unsound electronic throttle body can end up being the chief host inviting the error code P210E. So replacing one can be one of the wisest decisions to avoid a problematic system and a whole lot of problems including vacuum leaks and a failure in the electronic throttle control. Log in now!

Willing to know some common symptoms of OBD Code P210E? Your wish is our demand. Have a look at them below:

Common Symptoms

• A fall in the engine performance
• At times, one can observe the engine entering the limp home mode leading to a decreased performance

Here we have mentioned a few common measures that should be adopted in order to correct the error code P210E:

• Repair or replace a damaged wiring connector or “pig tail” on the throttle body
• A defective electronic throttle body should be mended or restored
• The engine management computer, if damaged should be repaired or replaced as soon as possible
• All the open or corroded wiring on the pigtail should be repaired or replaced
• The computer if not functioning should be reprogrammed
• A malfunctioning accelerator pedal sensor should be mended or restored. All its wiring should be inspected, if corroded or defective should be changed or repaired
• A jammed or broken TPS sensor should be mended or restored according to the requirements
• If required, the top cover of the throttle body should be changed or repaired

If you need parts to fix this issue, you no longer need to search for them. We at PartsAvatar Canada have an extensive range of auto parts throttle actuator, electronic throttle control system, throttle valve, accelerator pedal, accelerator pedal position sensor, PCM, throttle plate in stock from you, ranging from all replacement parts to all interior and exterior parts

If you want to easily diagnose this fault code P210E, then all you have to do is to follow the steps which are mentioned below:

• The first step is to check the TSBs (technical service bulletins) for the vehicle relating to the code online. Customer complaints, known problems or factory recommended repair procedure trigger TSBs
• It advised to search online or in a service manual for a revised procedure to reset the computer. For example, in a Nissan car, the ignition should be turned on and while you should wait for 3 seconds. Following this, in the next 5 seconds, the pedal should be depressed and released for 5 times. Next, halt for 7 seconds, and then the pedal should be pressed and held for the next 10 seconds. The pedal should be released, when the engine light begins to blink. Next, again wait for 10 seconds, the pedal should again be depressed for 10 seconds and released. The ignition should be turned off
• The electric connector should be pulled out of the throttle body. A careful inspection should be performed for the female terminals. Any corrosion should be cleaned using a small pocket screwdriver. A small amount of grease should be placed on the terminals to reconnect it
• If the terminal connector has any bent or missing pins, it is advised to pick up a few “pigtail” (available at almost every auto parts store)
• The top cover on the throttle body should be inspected for any cracks or warping. Repair or replace it after consulting from your dealer
• Utilizing a voltmeter, the accelerator pedal sensor should be examined. One can observe a 5 volts for reference and next to it a varying signal. Next, the key should be turned on while the pedal should be depressed slowly. The voltage should be seen climbing from .5 to 5.0. If the voltage spikes or there is no voltage at the signal wire, it should be replaced
• It is recommended to search online for the identification of wire terminals on the throttle body of the vehicle. The throttle body connector should be examined for power to the throttle motor. Also, have a helper turn the key on and slightly depress the pedal. A faulty computer should be blamed if there is no power. Also, if there is power a malfunctioning throttle body should be suspected

Common Mistakes When Diagnosing The P210E Code

Here we have listed a few common mistakes that should be avoided while diagnosing the error code P210E:

• A defective accelerator pedal position (APP) assembly
• A damaged powertrain control module (PCM)
• Throttle body assembly broken or jammed
• Wiring issues in the system