P20E0 - OBD Trouble Code
OBD Code P20E0 - Exhaust Aftertreatment Fuel Pressure Sensor Circuit High
The trouble code P20E0 can be explained as
Exhaust Aftertreatment Fuel Pressure Sensor Circuit High. This diagnostic fault
code is a generic powertrain code, which means that it would apply to the
OBD-II equipped vehicles. The specific repair steps can vary as it depends upon
the vehicle make and model. The engine control module, powertrain control
module or the transmission control module monitors this circuit depending upon
the particular automobile.
Learn More About OBD Error Code P20E0
If the engine control module would detect a variation in the voltage coming from the fuel pressure sensor circuit for the exhaust aftertreatment system that is outside the parameters set by the automobile manufacturer, then it would store the P20E0 error code. This would also give rise to the illumination of the check engine light.
What causes this problem with the Exhaust Aftertreatment Fuel Pressure Sensor Circuit High?
- Some issues related to the EAS fuel pressure sensor
- Malfunctioning EAS fuel supply pump
- Unlocked wiring in the EAS fuel pressure sensor circuit
- Unusable EAS controller/PCM or programming error
Replace/Repair These Parts To Fix Code P20E0
- Engine Control Module – Most of the time it is difficult to intercept the ECM faults and thus must be checked for thoroughly. There can be a problem with the circuit or the software might have malfunctioned. Thus repair, replace or reprogram the component as per requirement.
- Powertrain Control Module – If the PCM is faulty, it can stores wrong OBD codes and can lead to misdiagnosis. This can happen due to misinterpretation of data received from the various sensors and components which also affects the vehicle’s performance. Thus replace it immediately.
- Diagnostic Tools – Use factory grade diagnostic tools to resolve OBD code P20E0 error. Buy new diagnostic tools and equipment for us.
- Diesel Particulate Filter – The diesel particulate filter acts as an important component in managing the particulate emission in the exhaust system. If the filter is damaged, it may lead to increased emissions and pollutants through the tailpipe. Thus, replace damaged filter now!
- Diesel Exhaust Fluid Heater – If the diesel exhaust fluid heater is faulty, it will not be able to aid in conversion of harmful nitrous oxide compounds to nitrogen, carbon dioxide and water vapours to control emissions. Thus, replace it immediately.
- Exhaust System - Your exhaust system begins at the engine with the purpose of removing toxic gases and fumes from your vehicle. The components are a series of pipes, catalytic converters, sensors, mufflers, and often a resonator, as well as other emission devices. Thus, replace damaged exhaust system now!
- Fuel Injection – Damaged, corroded, leaky or clogged fuel injector will restrict fuel entry into the chamber and thus cause lean condition, hampering the overall performance. Replace it now!
Symptoms Of The OBD Error Code P20E0
There could be countless symptoms which that would accompany with this fault code. Willing to know some common symptoms of OBD Trouble Code P20E0? Your wish is our demand. Have a look at them below:
Common Symptoms
- Check engine light might come into signal
- Diminishing fuel efficiency
- A lot of black smoke might start emitting from the automobile’s exhaust
- Declining engine performance
How To Correct Exhaust Aftertreatment Fuel Pressure Sensor Circuit High Issue
Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:
- You must fix the defective PCM or programming error
- It is essential to restore the flawed EAS fuel pressure sensor circuit
- Repair or replace the quirky EAS controller
- Adjust the flawed EAS fuel supply pump
- Make sure to mend faulty electrical connection
- It is essential to restore the flawed EAS fuel pressure sensor
- Rehabilitate the defaults in the wiring harness
- Carefully adjust the leakage in the exhaust
Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of DTC, pcm, ecm, diesel particulate filter, fuel pressure sensor, electronic pump, diesel exhaust fluid, ohmmeter, body control module component and a lot more. We are sure that now all your issues would be resolved.
Easy Diagnosis Of Engine Error OBD Code P20E0
It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P20E0 code to be stored:
- The mechanic or the technician will use a diagnostic scanner or code reader like DVOM to visually scan for the error codes in the vehicle.
- After performing a careful inspection, every of the stored codes and freeze frame data are retrieved as it can help down the way for further diagnosis process.
- Then the mechanic should visually inspect the faulty as well as damaged parts.
- After that the scan tool should be utilized to inspect the EAS fuel supply system grounds and the EAS control system. Now once the EAS fuel supply system grounds has been fully inspected, there would be a need of a multimeter to inspect for proper voltage at the EAS control system.
- Check for the performance of the fuses with the circuit loaded and replace it, if required.
- Check for the voltage output of the EAS fuel pressure sensor and if it doesn’t match the desired parameters, the suspect for it to be faulty and replace it immediately.
Common Mistakes When Diagnosing The P20E0 Code
- Malfunctioning exhaust aftertreatment fuel pressure sensor
- There can be a failure in the powertrain control module
- Wiring problems