Error Code P2099 What It Means & What To Do?

<<See All OBD Codes

The trouble code P2099 can be explicated as Post Catalyst Fuel Trim System Too Rich Bank 2. This error code would indicate that the powertrain control module is malfunctioning in its ability to control fuel trims. Fuel trims are what the powertrain control module utilizes to decide whether to add fuel or remove fuel in order to keep the air/fuel ratio right for that specific vehicle.

This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. The engine control module, powertrain control module or the transmission control module monitors this circuit depending upon the particular automobile. This would give rise to the flashing up of the check engine light.

What causes this problem with the Post Catalyst Fuel Trim System Too Rich Bank 2?

• The catalytic converter might be flawed
• Imperfect mass air flow or manifold air pressure sensor
• Quirks in the O2 sensor/s
• Some issues related to the burnt, chafed, broken, or disconnected wiring and/or connectors
• Leakage in the engine exhaust

1. Oxygen Sensor – Oxygen sensor plays a vital role in anticipating the levels of oxygen measured for the optimal air to fuel ratios for the combustion process and also for the exhaust emissions to keep the emission levels under check. Thus, replace faulty oxygen sensor now!
2. Engine Control Module - Want to know the most common reason behind the failure in the engine control module? Corrosion or damage because of moisture can cause ECM failure. Corrosion might enter the ECM through the wiring harness and moisture can enter by a failure in the seals in the ECM itself.
3. Fuel Pressure Regulator – Without the fuel pressure regulator, the fuel rail will not be able to build up enough pressure to support the injectors with the sufficient amount of fuel, the fuel will instead flow straight through and not reach the injectors. Thus, replace faulty pressure regulator now!
4. Powertrain Control Module - The PCM makes the engine and transmission work in tandem. Any issue with the powertrain control module will cause major problems with the efficient running of the vehicle.
5. Mass Air Flow Sensor – Wrong information sent by the sensor will affect the engine performance adversely as it will not be able to properly read the air entering the system thus hampering the air to fuel ratios directly impacting the engine’s output. Thus, it is advisable to replace them in time.
6. Exhaust System Parts - A burning smell of the engine is likely to be seen as soon as there is a fault in any of the exhaust system parts. Also, performance issues are likely to arise due to a failure in the exhaust manifold. A leak or crack also leads to a reduction in the power, acceleration and efficiency of the vehicle. Repair or replace now.
7. Electronic Control Unit - If your vehicle fails to start for no apparent reason, this is also a good indicator that there can be some issues with the ECU. If you check the car battery, starter and other common electrical components, and the vehicle still does not start, a quirky electronic control unit should be the next logical thing to consider.
8. Diagnostic Tool - In order to fix these errors, you need a few diagnostic tools to get your car problems pointed out easily. Our diagnostic tools collection will come in handy to do so and resolve all your vehicle problems. Visit today!

It is vital to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P2099 here:

Common Symptoms

• Check engine light might come into signal
• Decline in the fuel efficiency
• Decreasing engine performance
• Storage of other associated diagnostic trouble codes

The repairs which you will have to do to correct this fault code are simply straightforward; you can surely pinpoint the necessary repairs on the basis of your diagnosis. Have a look at some common fixes:

• Make sure to mend the faulty manifold absolute pressure sensor
• It is essential to restore the flawed ECU
• Rehabilitate the defaults in the mass air flow sensor
• The malfunctioning fuel pressure regulator should be repaired or replaced as per the need
• Carefully adjust the faults in the powertrain control module
• Recondition the non-functioning oxygen sensor
• Adjust the flawed circuitry for the mass air flow sensor

Parts Avatar Canada is here to solve all your issues related to car parts. We have stocked a wide range of best priced powertrain control module, fuel pressure regulator, catalytic converter, oxygen sensor, mass airflow sensor, exhaust system, spark plug, exhaust system parts, O2 sensor, muffler, pcm car, ecm car, body control module component, air fuel ratio sensor and a lot more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• This is a general type of error code which is diagnosed with the help of a scanner.
• The mechanic will insert a scanner to diagnostic port of the vehicle and recover the codes and freeze frame data.
• If he happens to find any additional error codes, he has to address them as well.
• Once it is done, he has to reset the vehicle, and then test drive to see if the error code appears.
• If the error code does not return, then there can be an erratic condition.
• But, if the error code returns, then the mechanic has to check the fuel pressure regulator and oxygen sensor.
• If the fuel pressure regulator and oxygen sensor are defective, then it has to be replaced.
• Also, the mechanic can check for any sign of defects in the related parts, then he should quickly fix the issue.
• Then the mechanic has to check the wires, connectors and other electrical components and quickly replace them if he finds them to be damaged or defective.
• If the issues are not yet sorted out, then the mechanic will use a digital voltmeter/ ohmmeter and connect it to the vehicle.
• Once the circuit is inspected, he will thoroughly check all the harness and repair them accordingly.
• In most cases, this error code can arise mostly because of any shorted wires or dirty or manifold absolute pressure sensor.
• Whenever the mechanic or a trained professional, repairs any of the component like wires or connectors, he will reset the code and test drive the vehicle again to see if the error code appears again.
• This can actually help the mechanic to know if the problem is fixed.

Common Mistakes When Diagnosing The P2099 Code

• There are a lot of technicians who might restore the mass air flow sensor without even properly testing it as it is the most common cause of fuel trim codes.
• It is very essential to use all the diagnostic material which is available so that once can diagnose the check engine lights rightly. Check Engine Lights are the most common cause of misdiagnosis of any system on the automobile.