P206F - OBD Trouble Code

<<See All OBD Codes

Error code P206F? All you need is the Parts Avatar guide that’ll definitely help you comprehend the error code. It should be noted that the OBD-II code powertrain control module (PCM) failure in technical terms is also known as an intake manifold tuning (IMT) valve stuck closed bank 2. The intake manifold runner at higher RPM’ enables more air to flow through the intake. When the intake manifold runner fails to function as per the requirements, the error code P206F sets.

The intake manifold tuning valve (IMTV) situated on the intake manifold is actually a motorized actuated unit. The shutter connected to the actuator shaft is controlled by the IMTV actuator. The powertrain control module (PCM) has no monitor input with this system to signal the shutter position. It is notable that the motorized IMTV unit isn’t energized below approximately 2600 rpm or higher in numerous vehicles. In the intake manifold, the shutter is in a closed position, hence it does not allow any airflow blend to occur. The motorized unit is energized above approximately 2600 rpm or higher. The motorized unit is ordered by the powertrain control module initially at a 100 percent duty cycle to shift the shutter in order to open and then failing to approximately 50 cent to continue to hold the shutter open. During continuous key on engine off (KOEO), or key on engine running (KOER) self tests, the intake manifold tuning valve (IMTV) system is controlled for failures. Whenever the signal is more or less than the desired calibrated range, the test fails.

What causes this problem with the Intake Manifold Tuning (IMT) Valve Stuck Closed Bank 2?

• A damaged intake manifold tuning valve (IMTV)
• The harness in the intake manifold tuning valve (IMTV) open or short circuited
• An inadequate electrical connection in the intake manifold tuning valve (IMTV)
• A fault in the intake manifold runner control (IMRC)
• A jammed powertrain control module (PCM)

1. Powertrain Control Module - Because of a fault in the powertrain control module, downward emissions are likely to follow besides other issues like a sluggish engine crank, failure in the emission system etc. We advise you to get your faulty PCM changed now by simply logging into Parts Avatar.
2. Intake Manifold Tuning Valve - A defective intake manifold tuning valve accompanies problems like engine glitches, decrease in power and a poor fuel economy. Worried? Not anymore! Parts Avatar, your one stop destination has a solution for all your problems. Tune into Parts Avatar if you want to get rid of all these problems and the error code P206F.
3. Intake Manifold Tuning Valve Harness - Damaged intake manifold tuning valve harness can end up being the chief host inviting the error code P206F. In addition to the error code, it also invites problems a poor engine performance, weak acceleration and engine stalls. So, replacing one can be one of the wisest decisions to avoid a problematic system.
4. Intake Manifold Tuning Valve Circuit - Don’t know the root cause behind problems like difficulty while starting the vehicle? Is your intake manifold runner control sensor not working? It could all be due to a fault in the intake manifold tuning valve circuit. Mend or restore now.
5. Intake Manifold Runner Control Sensor - Experiencing a rough engine operation at idle? Deteriorating fuel economy? Reduced fuel economy? All this is triggered due to a fault in the intake manifold runner control sensor alongside the error code P206F. Change or repair now if you want to put an end to all these issues. Visit us today to get your hands on some of our awesome deals.
6. Dash Check Engine Light - In order to perform a diagnosis or dig into the actual cause of problems caused in the vehicle, it is essential to be aware of the error code. The error code is indicated by the dash check engine light. So fix your faulty one in order to maintain a sound system.
7. Intake Manifold Runner Control Actuator - Want to correct the error code P206F? Tired of all these problems hampering the overall drivability of the vehicle? Well, it could be all due to your malfunctioning intake manifold runner control actuator. Tune into Parts Avatar to get your new intake manifold runner control actuator right at your doorstep.

Interested in knowing the symptoms to obd code P206F? If yes, then you have arrived at the right place. We at PartsAvatar have listed out few common symptoms associated with this fuel injector problem.

Common Symptoms

• The engine light flashing on (or service engine soon warning light)

Wish to correct this error code with your vehicle? Do you know what all you should do to make your car free from this code? Well, don’t worry! We are here to guide you:

• Replace or repair a damaged intake manifold tuning valve (IMTV)
• All the harness in the intake manifold tuning valve (IMTV) that open or short circuited should be mended or restored
• Make sure you fix an inadequate electrical connection in the intake manifold tuning valve (IMTV)
• A malfunctioning intake manifold runner control (IMRC) should be repaired or replaced
• Fix a defective powertrain control module (PCM)

However, if you face any issue then we have stocked a wide range of best priced PCM, intake manifold tuning valve, intake manifold tuning valve harness, intake manifold tuning valve circuit, intake manifold runner control, engine light, intake manifold runner control actuator and more to help you out in fixing your car.

Thinking of where to start? How to diagnose the error code accurately? Well, then you should follow these steps in order to diagnose this fault code:

One should begin with a customary OBD-II trouble code scanner that should be employed to diagnose this trouble code P206F. This scanner should be used to verify and view the freeze frame data and assess the code by a qualified mechanic. The mechanic should also check for additional trouble codes stored too. After the repairs have been successfully performed, the codes should be cleared and the vehicle should be test driven to see if the code recurs. If the code vanish it could likely be due to a faulty diagnose or may represent an intermittent issue.

Common Mistakes When Diagnosing the P206F Code

• A defect in the intake manifold runner control actuator
• A broken powertrain control module (PCM)
• Complications due to wiring