P0C7B - OBD Trouble Code

<<See All OBD Codes

What does P0C7B error code mean? What does this error code signify? How can this error code be removed from the vehicle? Are you confused looking for a solution? Proceed reading the article further. The generator inverter voltage too high is usually referred to the wiring issues in the vehicle. The voltage which goes in and out of the inverter assembly is carefully looked after by the engine control module. If the original voltage fails to match with the requested voltage, then the error code, P0C7B will get stored in the vehicle.

The generator inverter is observed by the engine control module (ECM). The engine control module will set the error code in the vehicle if the factory specification is not met by the generator inverter.

What causes this problem with the Generator Inverter Voltage Too High?

• Defective generator inverter.
• The generator inverter harness might have an opening or short circuit.
• The generator inverter circuit might have a weak electrical connection.

1. Generator Inverter - With the help of generator inverter, the engine is attached to an alternator so that it can produce AC electricity. If you happen to find this generator inverter to be damaged, replace it quickly so that the engine functions normally and the P0C7B error is avoided.
2. Generator Inverter Harness - Usually the generator inverter harness has some wire cables and connectors along with it so that the terminals can be properly connected along with the engine throughout the vehicle. Any damage to the generator wiring harness must be quickly replaced so as to avoid engine malfunctioning.
3. Converter - Few of the inverters can be used as you drive your car because they have the ability to drain your car’s battery soon. Also, the peak efficiency of an inverter will range from 94% to 96. P0C7B error can be avoided if the damaged inverter is replaced soon.
4. Engine Control Module - You can easily find out that the engine control module in your vehicle is damaged if your vehicle faces issues like stalling or misfiring. Additionally, the behavior of the engine can be erratic. In one such scenario, it is always best to replace the faulty engine control module.
5. Engine Wiring Connectors - The engine wires run throughout the vehicle where their terminals are properly connected with the help of connectors. If these engine wires are not properly connected, then it can give rise to issues in your vehicle. Also, the damaged or shorted engine wiring connectors must be replaced as soon as possible.
6. Powertrain Control Module - You will likely face performance issue in your engine if the powertrain control module is faulty. Also, the engine may fail to start and there might be sparking issues. Get your powertrain control module fixed if you happen to witness these symptoms from your vehicle.

It is essential to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P0C7B here:

Common Symptoms

• The service engine warning light or else the engine light will stay on.

Here are some ways with the help of which you will be able to correct the OBD Code P0C7B

• The defective generator inverter has to be changed.
• Replacing the faulty inverter/converter.
• Broken engine wiring connectors need to be fixed.
• Powertrain control module and the engine control module has to be repaired.

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high-grade generator inverter, generator inverter harness, inverter, inverter battery, converter and a lot more for our precious customers.

Here are some steps which you should follow in order to diagnose this P0C7B fault code:

• This can actually help you to identify, if or not the malfunctioning is erratic.
• This is also a general type of error code, but unlike other diagnostic codes, it is always best to leave the diagnostic process to the experienced professionals as there are huge circuits involved.
• If the transmission fluid has a burnt smell, then you must quickly remove the transmission pan and visually examine if there are any clutch materials or any other debris.
• The main reasons for low pump pressure can be – the hydraulic passages that are blocked, the pump that is faulty, shift solenoids that are defective or may be an electronic pressure regulator which can be damaged.
• As you put your foot on the brakes of the car, you can likely expect your car to slow down or it might even come to a stop position.
• The amount of power that is applied on the brake pedal by your foot is aided with the help of hydraulic pressure.
• The force from your foot will engage with the piston and caliper where the brake pads are fixed (bonded abrasive and heat resistant metal or ceramic) so that you can apply pressure on the rotor.
• The OBD -II error code P0C7B is usually related to the cam that is camshaft timing.
• In one such scenario, if the timing of the cam is over- retarded then the illumination of the check engine light will take place and the error code P0C7B will get stored in the vehicle.

Common Mistakes When Diagnosing the P0C7B Code

• The inverter or the converter assembly might be faulty.
• Issues with the electrical wires.