P0C08 - OBD Trouble Code

It is always good to learn more! That is the reason why we are here to help you out in gaining more knowledge about the P0C08 error code. The thermistor resistance which is built into the motor temperature sensor would change as per the changes in the temperature of the MG2. Now if the temperature of the MG2 would be low, then the higher would be the resistance of the thermistor. Similarly, the increase in temperature would mean decrease in the resistance.

What causes this problem with the Drive Motor "B" Phase U-V-W Circuit/Open?

• There can be distorted hybrid vehicle motor assembly
• Hybrid vehicle motor assembly harness is open or small
• Hybrid vehicle motor assembly circuit might have inadequate electrical connection

1. Car Battery - There can be some issues with the Car Battery due to which you may see P0C08 code appearing over and over again. Visit us to buy best quality Car Battery online.
2. Electronic Control Unit - A lot of issues can arise do to defective Electronic Control Unit. Did you just see P0C08 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Body Control Module Component - Faulty Body Control Module Component can be the reason why P0C08 code is flashing. Visit us to purchase top notch Body Control Module Component online.
4. Motor Assembly Harness - It is an important auto part which needs full care. A faulty Motor Assembly Harness can be a reason behind the flashing up of P0C08 code.
5. Motor Assembly - OBD Code P0C08 can appear because of faulty Motor Assembly.
6. Hybrid Battery - There can be some issues with the Hybrid Battery due to which you may see P0C08 code appearing over and over again. Visit us to buy best quality Hybrid Battery online.
7. Engine Control Module - Are you facing some faults in your Engine Control Module? Don’t worry and get them replaced or else P0C08 code can turn up.
8. Powertrain Control Module - Common cause behind this P0C08 error code can be some fault in Powertrain Control Module. So it will be a good decision to replace them now.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0C08 code by mentioning some major symptoms below:

Common Symptoms

• The service engine soon light can start lighting up
• Issues in functioning of the high voltage system

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0C08:

• You must fix the defective hybrid battery
• Make sure to mend the faulty hybrid vehicle motor assembly
• It is essential to restore the flawed engine control module
• Repair or replace the quirky hybrid vehicle motor assembly harness
• The motor control module should be restored to working order

However, if you face any issue then we have stocked a wide range of best priced hybrid powertrain control module, body control module, power inverter and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• This is a general type of error code which is diagnosed with the help of a scanner.
• The mechanic will insert a scanner to diagnostic port of the vehicle and recover the codes and freeze frame data.
• If he happens to find any additional error codes, he has to address them as well.
• Once it is done, he has to reset the vehicle, and then test drive to see if the error code appears.
• If the error code does not return, then there can be an erratic condition.
• Then the mechanic has to check the wires, connectors and other electrical components and quickly replace them if he finds them to be damaged or defective.
• Check for the damaged hybrid battery and its components for error. It the mechanic finds the fault in the connectors in relation to the battery, replace it immediately.
• Also check for the particular battery cells emitting high voltages and thus might need battery replacement as well.
• A sure sign of this is smoke or steam being emitted from underneath the hood. The ignition timing could be set incorrectly and will require adjustment. If, when looking under the hood, you notice that the drive belts appear loose, they need to be tightened or completely replaced.
• If there is a noticeable pool of fluid underneath the car, this could be a sign of the cylinder head gasket failing. That will be confirmed in the form of billowing smoke being blown from the exhaust system.
• Parts or components should not be replaced with reference to only a P0C08 DTC. The vehicle service manual should be consulted for more information on possible causes of the fault, along with required testing.
• If all the components seems to work perfectly, inspect the PCM for faults and replacement along with reprogramming.

Common Mistakes When Diagnosing The P0C08 Code

• Non performance of the drive motor generator assembly
• The drive motor generator power inverter control module might not function properly