Error Code P0BF7: What It Means & What To Do?

<<See All OBD Codes

The trouble code P0BF7 can be explicated as Drive Motor ‘B’ Phase V Current Sensor Circuit Low. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

The drive motor generator power inverter control module would monitor and regulate the high voltage system as well as drivetrain constituents. This module would run self-checks to safeguard that it is capable of properly performing its needed functions. Now if the error would be detected, then the P0BF7 trouble code would start indicating.

What causes this problem with the Drive Motor ‘B’ Phase V Current Sensor Circuit Low?

• There can be distorted hybrid vehicle motor assembly
• Hybrid vehicle motor assembly harness is open or small
• Hybrid vehicle motor assembly circuit might have inadequate electrical connection

1. Hybrid Drive Cooling Pump - Check for faults in the hybrid battery cooling pump and replace it, if required. If the cooling pump does not function properly, then the battery might not work to its full capacity and can cause serious performance issues.
2. Battery Temperature Sensor - Inspect for faulty battery temperature sensor as it may cause the battery to overheat and not work properly and cause serious physical damages to various starting and charging system components. Thus, replace faulty sensor now!
3. Hybrid Battery - The battery itself can be faulty and can be overheating, which can lead to faster discharge and slower charging, with risks of leakages and other damages to the vehicle. Thus, immediate replacement is advisable.
4. Engine Control Module - Want to know the most common reason behind the failure in the engine control module? Corrosion or damage because of moisture can cause ECM failure. Corrosion might enter the ECM through the wiring harness and moisture can enter by a failure in the seals in the ECM itself.
5. Car Battery - Faulty car battery can have the problem of overheating and fast discharging. Thus, it can affect the motor performance as well as damaged major components. Replace it immediately.
6. Powertrain Control Module - The PCM makes the engine and transmission work in tandem. Any issue with the powertrain control module will cause major problems with the efficient running of the vehicle.
7. Electronic Control Unit - If your vehicle fails to start for no apparent reason, this is also a good indicator that there can be some issues with the ECU. If you check the car battery, starter and other common electrical components, and the vehicle still does not start, a quirky electronic control unit should be the next logical thing to consider.
8. Inverter Cooler Pump - The inverter cooler pump can also be faulty and not respond to the PCM instructions. This means that even though the temperature sensor and the PCM are working properly, the cooler pump may not work and cause damage to the battery functions. Thus, replace it immediately.

It is essential to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P0BF7 here:

Common Symptoms

• Illumination in the service engine soon light

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0BF7:

• The malfunctioning hybrid vehicle motor assembly should be repaired or replaced as per the need
• Carefully adjust the faults in the hybrid vehicle motor assembly harness
• The hybrid vehicle motor assembly circuit should be restored to working order

Parts Avatar Canada is here to solve all your issues related to car parts. We have stocked a wide range of best priced battery control module, hybrid vehicle motor assembly, inverter control module, hybrid vehicle motor assembly harness, hybrid battery, pcm, ecm, ecu, pcm module and ecm module and a lot more to help you out in fixing your car.

If you want to easily diagnose this trouble code, then you must follow the steps which are mentioned here as below:

• The mechanic or the technician will use a diagnostic scanner or code reader like DVOM to visually scan for the error codes in the vehicle.
• After performing a careful inspection, every of the stored codes and freeze frame data are retrieved as it can help down the way for further diagnosis process.
• Most often he has to inspect the Drive Motor ‘B’ Phase V Current Sensor Circuit itself to see if they are faulty or damaged. Additional error codes that are stored in the vehicle are also addressed.
• The mechanic performs a continuity test between the PCM and solenoid to check the resistance.
• If the solenoid or the control modules are not faulty, he will then retune the code and test drive the vehicle.
• On test driving, if the P0BF7 code does not return soon, he will know that an erratic condition exits.
• But if the error returns instantaneously, he will check every component of the control module as well as the circuit like connectors, wires, harness, fuses etc for any possible fault.
• If any component is damaged, he will fix them right away.
• After performing this repair, he will inspect the Drive Motor ‘B’ Phase V Current Sensor Circuit as well.
• If the level is below the manufacturer’s specification, it has to be refilled and if the fluid is murky or contaminated it needs to be replaced.
• Every time a repair work is carried out, make sure that the mechanic test drives the vehicle after every repair so that the diagnosis is successful. This can eventually help him to know as to where the error occurred.

Common Mistakes When Diagnosing The P0BF7 Code

• Quirks in the drive motor generator power inverter control module
• Issues related with the wiring