P0AED OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0AED can be defined as Drive Motor Inverter Temperature Sensor “A” Circuit. With the help of multiple sensors, the temperature of each battery cell is carefully looked after by the hybrid battery pack. If an unlikely signal is reported by at least one of the battery temperature sensors, a P0AED error code will be set. The disabling of a high voltage system will occur if multiple sensors fail.

There are 3 locations available for the battery temperature sensor in the HV battery. In each battery temperature sensor, thermistor’s resistance is built and it will vary in correspondence to the HV battery temperature. If the battery temperature is low, the resistance of thermistor will be high. On the contrary, if the temperature is high, resistance will be low. The HV control ECU finds the HV battery temperature with the help of battery temperature sensors. The power management control ECU then receives the identified value. Based on the results of this identification, the blower fan is controlled by the power management control ECU.

What causes this problem with the Drive Motor Inverter Temperature Sensor “A” Circuit?

• Some flaws in the inverter with converter assembly
• Inverter with converter assembly harness might be opened or sometimes shorted
• Inverter with converter assembly circuit might have inadequate electrical connection
• Malfunctioning HV control ECU

1. Battery Temperature Sensor - The temperature sensor is important to keep the battery from overheating. Thus, if the temperature sensor is faulty, it must be replaced immediately. Buy new temperature sensor from us at equitable prices now!
2. Hybrid Battery - Faulty hybrid battery may overheat or discharge quickly, causing drivability issues. It can affect the acceleration and throttle response and can also cause damage to various parts. Replace the faulty hybrid battery now!
3. Engine Control Module - There can be some engine performance issues due to faulty engine control module. If the ECM fails or has any problems it can lead to performance issues with the vehicle like misfires, hesitation, loss of power, and sometimes even decreased fuel economy.
4. Powertrain Control Module - PCM stands for powertrain control module. It is a car part, a control unit which is utilized on motor vehicles. It is generally a combined control unit, consisting of the engine control unit (ECU) and the transmission control unit (TCU).
5. Inverter Cooler Pump - Inverter cooler pump is responsible for keeping the boost converter temperatures under control. Thus, if it is not functioning properly, the converter can overheat and result in underperformance of the system. Buy new cooler pump and replace in now!
6. Electronic Control Unit - If your automobile's check engine light remains on constantly, and never goes off, there's a good chance that your vehicle has a damaged electronic control unit. There are a lot of reasons why a car's check engine light will remain on. The most common reason is a defective ECU.
7. Diagnostic Tool - You will need high grade diagnostic tools for correction of the OBD error code which is detected. Visit us today to grab amazing deals

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0AED code by mentioning some major symptoms below:

Common Symptoms

• The service engine soon light can start lighting up

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0AED:

• It is important to restore the flawed inverter with converter assembly harness
• Repair or replace the quirky powertrain control module
• Rehabilitate the defaults in the inverter with converter assembly
• Carefully adjust the faults in the inverter with converter assembly circuit
• Recondition the non-functioning HV control ECU

However, if you face any issue then we have stocked a wide range of best priced HV battery temperature sensor, Inverter with converter assembly, HV control ECU, Inverter with converter assembly harness, hv battery, pcm, ecm, ecu, pcm module, ecm module and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• Use an OBD-II scanner in order to verify that the code is present, and check for other codes for any other type of error or problem that might need attention.
• The current data along with freeze frame data are recorded, and the codes are then cleared to see if they reoccur.
• The vehicle is inspected for any problems with the wiring and connectors to check for loose connections, corrosion, or shorts.
• The tests related to the drive motor inverter temperature sensor “A” circuit and components may help pinpoint the problem, as well as inspection of the current sensor and cut off switch will further be helping the cause.
• The P0AED error is triggered if there is a physical problem with the drive motor inverter temperature sensor “A” circuit which could cause the engine performance to go off.

Common Mistakes When Diagnosing the P0AED Code

• Nonperformance of the inverter/converter assembly
• Failure in the car wiring