Guide To P0AC1 OBD Error Code Solutions

<<See All OBD Codes

The trouble code P0AC1 can be defined as Hybrid Battery Pack Current Sensor “A” Circuit Low. The battery current sensor is mounted on the positive cable side of the HV battery assembly which would detect the amperage that would flow into the HV battery. The battery smart unit would input a voltage which varies between 0 and 5 V in proportion to the amperage, into the IB terminal from the battery current sensor. If there is an output voltage of the battery current sensor that is below 2.5 V, then it would indicate that the HV battery is being discharged, and when it would be above 2.5 V, then it would indicate that the HV battery is being charged.

The hybrid battery pack current sensor “A” circuit is being monitored by the battery control module. This trouble code would be set by the battery control module when the hybrid battery pack current sensor “A” circuit would not be as per the specifications set by the manufacturer. The engine control module, powertrain control module or the transmission control module monitors this circuit depending upon the particular automobile.

What causes this problem with the Hybrid Battery Pack Current Sensor “A” Circuit Low?

• Some flaws in the battery smart unit
• Battery smart unit harness might be opened or sometimes shorted
• Battery smart unit circuit might have inadequate electrical connection
• Malfunctioning hybrid battery junction block

1. Battery Temperature Sensor - The temperature sensor is important to keep the battery from overheating. Thus, if the temperature sensor is faulty, it must be replaced immediately. Buy new temperature sensor from us at equitable prices now!
2. Hybrid Battery - Faulty hybrid battery may overheat or discharge quickly, causing drivability issues. It can affect the acceleration and throttle response and can also cause damage to various parts. Replace the faulty hybrid battery now!
3. Engine Control Module - There can be some engine performance issues due to faulty engine control module. If the ECM fails or has any problems it can lead to performance issues with the vehicle like misfires, hesitation, loss of power, and sometimes even decreased fuel economy.
4. Powertrain Control Module - PCM stands for powertrain control module. It is a car part, a control unit which is utilized on motor vehicles. It is generally a combined control unit, consisting of the engine control unit (ECU) and the transmission control unit (TCU).
5. Inverter Cooler Pump - Inverter cooler pump is responsible for keeping the boost converter temperatures under control. Thus, if it is not functioning properly, the converter can overheat and result in underperformance of the system. Buy new cooler pump and replace in now!
6. Electronic Control Unit - If your automobile's check engine light remains on constantly, and never goes off, there's a good chance that your vehicle has a damaged electronic control unit. There are a lot of reasons why a car's check engine light will remain on. The most common reason is a defective ECU.
7. Diagnostic Tool - You will need high grade diagnostic tools for correction of the OBD error code which is detected. Visit us today to grab amazing deals.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0AC1 code by mentioning some major symptoms below:

Common Symptoms

• The service engine soon light can start lighting up

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0AC1:

• It is essential to restore the flawed battery smart unit harness
• Repair or replace the quirky powertrain control module
• Rehabilitate the defaults in the battery smart unit
• Carefully adjust the faults in the battery smart unit circuit
• Recondition the non-functioning hybrid battery junction block

However, if you face any issue then we have stocked a wide range of best priced HV battery temperature sensor, HV battery assembly, battery smart unit, HV battery assembly harness, hv battery, pcm, ecm, ecu, pcm module, ecm module and more to help you out in fixing your car

Here are some steps which you should follow in order to diagnose this fault code:

• Use an OBD-II scanner in order to verify that the code is present, and check for other codes for any other type of error or problem that might need attention.
• The current data along with freeze frame data are recorded, and the codes are then cleared to see if they reoccur.
• The vehicle is inspected for any problems with the wiring and connectors to check for loose connections, corrosion, or shorts.
• The tests related to the hybrid battery pack current sensor “A” circuit and components may help pinpoint the problem, as well as inspection of the current sensor and cut off switch will further be helping the cause.
• The P0AC1 error is triggered if there is a physical problem with the hybrid battery pack current sensor “A” circuit which could cause the engine performance to go off.

Common Mistakes When Diagnosing The P0AC1 Code

• Non-performance of the battery control module
• Defaults in the battery current sensor
• Failure in the high voltage battery assembly