P0A2E OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0A2E can be described as Drive Motor "A" Temperature Sensor Circuit Intermittent. The resistance of the thermistor which is built into the motor temperature sensor would change as per the changes in the temperature of the MG2. Now if the temperature of the MG2 would be low, then the higher would be the resistance of the thermistor. In the similar way, the rise in temperature would mean fall in the overall resistance. This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code.

Error code P0A2E flashing? We have a wide range of automobile parts and accessories. We won’t let you down in any way as for us our customers are everything. Visit us as fast as you can. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model. Now when the PCM or any of the other control modules would indicate faults in the Drive Motor "A" Temperature Sensor Circuit, then it would give rise to the P0A2E trouble code.

What causes this problem with the Drive Motor "A" Temperature Sensor Circuit Intermittent?

• There can be inferior electrical connection in the hybrid vehicle motor circuit
• Some defects in the hybrid vehicle motor
• Opened or shorted hybrid vehicle motor harness

1. Automatic Transmission Sensor -. Buy high grade Automatic Transmission Sensor online from Parts Avatar Canada.
2. Engine Control Module - There can be some issues with the Engine Control Module due to which you may see P0A2E code appearing over and over again. Visit us to buy best quality Engine Control Module online.
3. Auto Transmission Control Module - Are you facing some faults in your Automatic Transmission Control Module? Don’t worry and get them replaced or else P0A2E code can turn up.
4. Engine Coolant Temperature Sensor - Common cause behind this P0A2E error code can be some fault in Engine Coolant Temperature Sensor. So, it will be a good decision to replace them now.
5. Powertrain Control Module - Automatic Transmission Module is perfectly fine but still but having that trouble code P0A2E flashing? In such a situation your Powertrain Control Module might be faulty. Why don’t you think of getting that replaced?
6. Auto Transmission Shift Solenoid - The P0A2E code can also arise due to some issues in Auto Transmission Shift Solenoid. So, it is advised to replace them as soon as possible.
7. Body Control Module Component - P0A2E code does not really end up spoiling your Auto Transmission Shift Solenoid, but it might also accompany few Body Control Module Component issues. We have best Body Control Module Component with us.

We care for our customers and that’s why we can totally understand your problem. That’s the reason why we have listed out some major symptoms behind the flashing up of OBD Code P0A2E. They are mentioned here as follows:

Common Symptoms

• Non-operational high voltage system

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0A2E:

• It is essential to restore the flawed electronic control unit
• Repair or replace the defaults in the hybrid vehicle motor circuit
• Rehabilitate the quirky hybrid vehicle motor
• The malfunctioning hybrid vehicle motor harness should be repaired or replaced as per the need
• Carefully adjust the faults in the ECM/PCM
• It is necessary to perform proper service of the unsound engine coolant temperature sensor

Now are you thinking that from where will you purchase these car parts? You have arrived at the right place. We at Parts Avatar care for our customers, that’s why we provide best quality of Motor, diesel particulate filter, diesel particulate filter cleaner, electronic control module, engine temperature sensor, electronic brake control module at marketable prices.

Do you wish to diagnose P0A2E error code easily? Here are some steps which you should follow in order to diagnose this fault code:

• As an initial step the mechanic will carefully inspect the vehicle with the help of a scanner.
• After this, the technician will connect a scanner to the diagnostic code so that he can recover all the codes and freeze frame data.
• Note down this information as it can clearly help for further diagnosis.
• The mechanic will also inspect the shift solenoid to find if it is disconnected or if any other faults persist.
• After careful inspection, he will reset the code and test drive your vehicle to check for reappearance of the codes.
• He will know that an intermittent condition persists, if the code does not return instantly.
• But if the error code returns quickly, the vehicle is test driven, and then he has to inspect the transmission fluid.
• If any of the component is damaged, the mechanic will replace them quickly.
• Most often, whenever the mechanic carries out any repair work, he will reset the code and test drive your car, to check if the codes return immediately. This can preferably help the mechanic to know what caused this error code in the vehicle.

Common Mistakes When Diagnosing The P0A2E Code

• Faults in the high voltage motor