P0A28 - OBD Trouble Code

<<See All OBD Codes

The trouble code P0A28 can be described as Hybrid Battery Power Off Circuit Low. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

Error code P0A28 flashing? Steer to our amazing website for a wide range of automobile parts and accessories. We won’t let you down in any way as for us our customers are everything. Visit us as fast as you can. The hybrid battery is being monitored by the engine control module. This trouble code would be set by the ECM when the hybrid battery would not be as per the specifications set by the manufacturer.

What causes this problem with the Hybrid Battery Power Off Circuit Low?

• There can be inoperative hybrid battery cut off switch
• There can be opened or shorted hybrid battery cut off switch harness
• Hybrid battery cut off switch circuit inferior electrical connection

1. Car Battery - Did your mechanic just found out that there is some fault in the Car Battery? Buy top notch Car Battery from us at economical prices.
2. Battery Current Sensor - A broken Battery Current Sensor can cause a lot of issues. It would be nice if you get it replaced on time.
3. Hybrid Battery - Everything is fine with the engine control module and still OBD code P0A28 flashing? Then there is definitely some fault with the Hybrid Battery. Get it checked and replace if needed.
4. Battery Coolant Pump - Battery Coolant Pump is an important car part which should never be neglected. May be there is some fault in it due to which P0A28 code may start flashing.
5. Engine Control Module - A faulty Engine Control Module can be troublesome. You can always rely on us as we have best auto parts for our customers.

We care for our customers and that’s why we can totally understand your problem. That’s the reason why we have listed out some major symptoms behind the flashing up of OBD Code P0A28. They are mentioned here as follows:

Common Symptoms

• The service engine soon light can start lighting up
• Non-operational high voltage system

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0A28:

• You must fix the defective hybrid battery cut off switch harness
• Make sure to mend the faulty battery current sensor
• Repair or replace the quirky car battery
• Rehabilitate the defaults in the hybrid battery cut off switch
• The malfunctioning hybrid battery cut off switch circuit should be repaired or replaced as per the need
• Carefully adjust the faults in the hybrid battery cut off switch circuit
• It is necessary to perform proper service of the unsound hybrid battery 

Now are you thinking that from where will you purchase these car parts? You have arrived at the right place. We at Parts Avatar care for our customers, that’s why we provide best quality of battery cut off switch, harness, battery isolator, battery disconnect switch, tics transmission at marketable prices.

Do you wish to diagnose P0A28 error code easily? Here are some steps which you should follow in order to diagnose this fault code:

• The mechanic or the technician will use a diagnostic scanner or code reader like DVOM to visually scan for the error codes in the vehicle.
• After performing a careful inspection, every of the stored codes and freeze frame data are retrieved as it can help down the way for further diagnosis process.
• Most often he has to inspect the solenoid itself to see if they are faulty or damaged. Additional error codes that are stored in the vehicle are also addressed.
• The mechanic performs a continuity test between the PCM and solenoid to check the resistance.
• If the solenoid or the control modules are not faulty, he will then retune the code and test drive the vehicle.
• On test driving, if the P0A28 code does not return soon, he will know that an erratic condition exits.
• But if the error returns instantaneously, he will check every components of the control module as well as the circuit like connectors, wires, harness, fuses etc for any possible fault.
• If any component is damaged, he will fix them right away.
• After performing this repair, he will inspect the transmission fluid as well as its level.
• If the level is below the manufacturer’s specification, it has to be refilled and if the fluid is murky or contaminated it needs to be replaced.
• Every time a repair work is carried out, make sure that the mechanic test drives the vehicle after every repair so that the diagnosis is successful. This can eventually help him to know as to where the error occurred.

Common Mistakes When Diagnosing the P0A28 Code

• Some issues related to the wiring
• Faults in the high voltage battery assembly