Guide To P0A1B OBD Error Code Solutions

<<See All OBD Codes

The trouble code P0A1B can be described as Drive Motor "A" Control Module. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

Don’t worry if P0A1B error code is triggering again and again. We offer wide range of auto parts at affordable prices to our dear customers. It is the MG ECU which is situated in the inverter with converter assembly which would monitor its interior operation and then this trouble code would be set when it would detect some malfunctions.

What causes this problem with the Drive Motor "A" Control Module?

• There can be inoperative inverter with converter assembly
• There can be opened or shorted Inverter with converter assembly harness
• There can be poor electrical connection in the Inverter with converter assembly

1. Auto Transmission Control Module - Do you remember when was the last time you got your car Auto Transmission Control Module checked up? A dirty Auto Transmission Control Module can cause a lot of issues like displaying P0A1B code.
2. Electronic Control Unit - Poor Electronic Control Unit can cause a lot of difficulties, so why not get it replaced at time?
3. Powertrain Control Module - Are there some faults in your Powertrain Control Module? Don’t waste time and get them replaced or else P0A1B code can turn up.
4. Engine Control Module - OBD Code P0A1B can appear because of faulty Engine Control Module.
5. Body Control Module Component - Everything is fine with Engine Control Module and still P0A1B code triggering? Then you must get your Body Control Module Component checked.
6. Catalytic Converter - There can be some issues with the Catalytic Converter due to which you may see P0A1B code appearing over and over again. Visit us to buy best quality Catalytic Converter online.
7. Auto Transmission Shift Solenoid - A lot of issues can arise do to defective Auto Transmission Shift Solenoid. Did you just see P0A1B code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.

Our main motive is to achieve customer satisfaction and that’s why we will help you to diagnose P0A1B code by mentioning some major symptoms below:

Common Symptoms

• Check engine light might come into signal

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0A1B:

• You must fix the defective inverter with converter assembly harness
• Repair or replace the quirky engine control module
• The inverter with converter assembly should be restored to working order
• It is necessary to perform proper service of the unsound inverter with converter assembly circuit

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Automatic Transmission Module, Solenoid Car, Ford Focus Transmission Parts, Ecm Car, Electronic Control Module, Engine Control Unit, Ecu Chip and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• As an initial step the mechanic will carefully inspect the vehicle with the help of a scanner.
• After this, the technician will connect a scanner to the diagnostic code so that he can recover all the codes and freeze frame data.
• Note down this information as it can clearly help for further diagnosis.
• The mechanic will also inspect the shift solenoid to find if it is disconnected or if any other faults persist.
• After careful inspection, he will reset the code and test drive your vehicle to check for reappearance of the codes.
• He will know that an intermittent condition persist, if the code does not return instantly.
• But if the error code returns quickly, the vehicle is test driven, and then he has to inspect the transmission fluid.
• If any of the component is damaged, the mechanic will replace them quickly.
• Most often, whenever the mechanic carries out any repair work, he will reset the code and test drive your car, to check if the codes return immediately. This can preferably help the mechanic to know what caused this error code in the vehicle.

Common Mistakes When Diagnosing The P0A1B Code

• Inverter/converter assembly might start failing

P0A1C - Drive Motor "B" Control Module