P0958 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0958 can be defined as Auto Shift Manual Mode Circuit High. This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another. This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code.

It is always good to learn more! That is the reason we are here to help you out in gaining more knowledge about the P0958 error code. The P0958 is an OBD-II generic code and it will appear if auto shift manual mode circuit would increase or decrease to a level that is not within the limits which have been programmed.

What causes this problem with the Auto Shift Manual Mode Circuit High?

• Defective auto shift manual switch
• Auto shift manual switch harness is unlocked
• Auto shift manual switch circuit poor electrical connection

1. Body Control Module Component - Did your mechanic just found out that there is some fault in the Body Control Module Component? Buy top notch Body Control Module Component from us at economical prices.
2. Auto Transmission Control Module - A broken Auto Transmission Control Module can cause a lot of issues. It would be nice if you get it replaced on time.
3. Auto Transmission Shift Solenoid - Everything is fine with the engine control module and still OBD code P0958 flashing? Then there is definitely some fault with the Auto Transmission Shift Solenoid. Get it checked and replace if needed.
4. Electronic Control Unit - Electronic Control Unit is an important car part which should never be neglected. May be there is some fault in it due to which P0958 code may start flashing.
5. Engine Control Module - A faulty Engine Control Module can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Powertrain Control Module - If everything is alright with Auto Transmission Shift Solenoid, then there is surely some defect in Powertrain Control Module. Get it replaced before the situation gets worse.
7. Gear Shift Extension - P0958 code can display due to some issues in the Gear Shift Extension. So it is very important to replace the Gear Shift Extension with us at equitable prices.

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0958 code by mentioning some major symptoms below:

Common Symptoms

• Autostick shifting might not be proper
• Illumination in the service engine soon light

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0958:

• You must fix the defective electronic control unit
• Make sure to mend the faulty body control module component
• It is essential to restore the flawed powertrain control module
• Repair or replace the quirky auto shift manual switch
• Rehabilitate the defaults in the gear shift
• Carefully adjust the faults in the auto shift manual switch harness

However, if you face any issue then we have stocked a wide range of best priced cvt transmission parts, steering wheel covers, hurst shifter, paddle shift, 700R4 transmission parts, zf transmission parts, 4L60E transmission parts, 4L80E transmission parts, standard transmission parts and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• The P0958 error code can be diagnosed by utilizing an OBD-II trouble code scanner.
• A scanner should be used by a professional technician to notice the freeze frame data, to assemble details about the code.
• The mechanic can also check to see if there is presence of additional trouble codes.
• Now if there are a number of codes, then they should be addressed in the same order in which they are appearing on the scanner.
• After that the mechanic should reset the trouble codes, restart the vehicle, and check to see if the code remains detected.
• If it does not, then the code was likely triggered incorrectly, or represents an intermittent issue.

Common Mistakes When Diagnosing The P0958 Code

• Negligence in the autostick shift switch
• Malfunctioning powertrain control module
• Problems associated with the wiring