Guide To P0947 OBD Error Code Solutions

<<See All OBD Codes

The trouble code P0947 can be defined as Hydraulic Pump Relay Circuit Low. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another. This trouble code would give to the illumination of the check engine light.

It is always good to learn more! That is the reason we are here to help you out in gaining more knowledge about the P0947 error code. The hydraulic oil temperature sensor is being monitored by the transmission control module. This error code would be set by the TCM when the hydraulic oil temperature sensor would not be as per the parameters set by the manufacturer.

What causes this problem with the Hydraulic Pump Relay Circuit Low?

• Less transmission fluid
• The transmission fluid might not be clean
• There can be inoperative wiring or related electrical connector
• Some issues related to the hydraulic pump relay
• The transmission control module might be damaged
• Quirks in the engine control module

1. Air Pressure Gauge - Did your mechanic just found out that there is some fault in the Air Pressure Gauge? Buy top notch Air Pressure Gauge from us at economical prices.
2. Engine Oil Pressure Switch - A broken Engine Oil Pressure Switch can cause a lot of issues. It would be nice if you get it replaced on time.
3. Body Control Module Component - Everything is fine with the engine control module and still OBD code P0947 flashing? Then there is definitely some fault with the Body Control Module Component. Get it checked and replace if needed.
4. Hydraulic Oil Temperature Sensor - Hydraulic Oil Temperature Sensor is an important car part which should never be neglected. May be there is some fault in it due to which P0947 code may start flashing.
5. Powertrain Control Module - A faulty Powertrain Control Module can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Auto Transmission Shift Solenoid - If everything is alright with PCM, then there is surely some defect in Auto Transmission Shift Solenoid. Get it replaced before the situation gets worse.
7. Oil Pressure Sender - P0947 code can display due to some issues in the Oil Pressure Sender. So it is very important to replace the Oil Pressure Sender with us at equitable prices.
8. Auto Transmission Control Module - OBD Code P0947 can appear because of faulty Auto Transmission Control Module. 

Our main motive is to achieve customer satisfaction as for us our customers are everything and that’s why we will help you to diagnose P0947 code by mentioning some major symptoms below:

Common Symptoms

• Check engine light might come into signal
• The automobile might shift forcefully
• The car might not skid at all
• There might be transmission sliding

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0947:

• You must fix the defective transmission control module
• Make sure to fill transmission fluid to manufacturer-recommended levels
• It is essential to perform a perform a transmission fluid flush
• Repair or replace the quirky engine control module
• Rehabilitate the defaults in the wiring and electrical components
• The malfunctioning hydraulic pump relay circuit should be repaired or replaced as per the need
• Carefully adjust the faults in the defective hydraulic pump

However, if you face any issue then we have stocked a wide range of best priced Diesel Particulate Filter, Pressure Control Solenoid, Hydraulic Pressure Sensor, Line Pressure Sensor, Dpf Filter, Diesel Particulate Filter and more to help you out in fixing your car.

Here are some steps which you should follow in order to diagnose this fault code:

• You can use an OBD-II scanner to inspect the P0947 trouble code.
• Inspect the transmission fluid levels.
• Scan the quality of the transmission fluid.
• Examine transmission pan for possible debris, including clutch debris, which could be the sign of a larger
• transmission associated issue.
• Visually check the wiring and electrical constituents associated to the hydraulic pump relay circuit for
• possible defect.
• The harness from the transmission control module to the transmission for any signs of faults should be inspected
• properly.
• Survey the resistance across terminals.
• The resistance test at transmission connector should be repeated if resistance is not at normal levels.

Common Mistakes When Diagnosing The P0947 Code

Many a times the mechanics make mistake of not inspecting the level of the transmission fluid as well as its quality. The vehicle should be taken out for a test drive and it should be rescanned to have a look if the code is appearing before you start performing complicated diagnosis as well as repairs.