P0942 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0942 can be elucidated as Hydraulic Pressure Unit. The transmission control system electronically controls the line pressure. It is then measured by the line pressure sensor. The line pressure which is desired would be compared to the actual line pressure. It would then be regulated by electronically changing the duty cycle of the pressure control solenoid. The line pressure would be calculated by the transmission control system as it is based upon the inputs from the transmission as well as from the car engine. A calculated torque input to the transmission is used as the main input to the desired line pressure calculation and is known as torque based line pressure. The transmission control module would then monitor the hydraulic pressure sensor. The TCM sets the OBDII code when the hydraulic pressure sensor would not be as per the factory specifications.

Are you tensed because the P0942 fault code is flashing? We have everything which you need and at equitable prices. You must visit us and we promise that you will never regret your decision. If the powertrain control module would detect an issue with the hydraulic pressure unit, then it would give rise to the P0942 error code. The particular code which is triggered depends upon the specific fault which the PCM has detected.

What causes this problem with the Hydraulic Pressure Unit?

• Issue of less transmission fluid level
• Some issues related to the shift lever position
• Transmission filter might be flawed
• Imperfect transmission oil pump

1. Engine Oil Pressure Switch - There can be some issues with the Engine Oil Pressure Switch due to which you may see P0942 code appearing over and over again. Visit us to buy best quality Engine Oil Pressure Switch online.
2. Air Pressure Gauge - A lot of issues can arise do to defective Air Pressure Gauge. Did you just see P0942 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Auto Transmission Control Module - Faulty Auto Transmission Control Module can be the reason why P0942 code is flashing. Visit us to purchase top notch Auto Transmission Control Module online.
4. Oil Pressure Sender - It is an important auto part which needs full care. A faulty Oil Pressure Sender can be a reason behind the flashing up of P0942 code.
5. Powertrain Control Module - OBD Code P0942 can appear because of faulty Powertrain Control Module.
6. Hydraulic Oil Temperature Sensor - There can be some issues with the Hydraulic Oil Temperature Sensor due to which you may see P0942 code appearing over and over again. Visit us to buy best quality Hydraulic Oil Temperature Sensor online.
7. Body Control Module Component - Are you facing some faults in your Body Control Module Component? Don’t worry and get them replaced or else P0942 code can turn up.
8. Auto Transmission Shift Solenoid - Common cause behind this P0942 error code can be some fault in Auto Transmission Shift Solenoid. So it will be a good decision to replace them now.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Illumination in the service engine soon light
• There can be a delay in the shifting

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• You must fix the issue of the low transmission fluid level
• The transmission oil pump should be restored to working order
• It is necessary to perform proper service of the unsound transmission filter
• Adjust the flawed shift lever position 

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Diesel Particulate Filter, Pressure Control Solenoid, Hydraulic Pressure Sensor, Line Pressure Sensor, Dpf Filter, Diesel Particulate Filter and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

As an initial step the mechanic will carefully inspect the vehicle with the help of a scanner. After this, the technician will connect a scanner to the diagnostic code so that he can recover all the codes and freeze frame data. Note down this information as it can clearly help for further diagnosis. The mechanic will also inspect the shift solenoid to find if it is disconnected or if any other faults persist. After careful inspection, he will reset the code and test drive your vehicle to check for reappearance of the codes. He will know that an intermittent condition persist, if the code does not return instantly. But if the error code returns quickly, the vehicle is test driven, and then he has to inspect the transmission fluid.

Once the fluid is checked for appropriate level, then every other components like wires and connectors have to be checked for possible damages. If any of the component is damaged, the mechanic will replace them quickly. Most often, whenever the mechanic carries out any repair work, he will reset the code and test drive your car, to check if the codes return immediately. This can preferably help the mechanic to know what caused this error code in the vehicle.

Common Mistakes When Diagnosing The P0942 Code

• Failure in the hydraulic oil temperature sensor
• There can be some faults in the transmission control module
• Wiring issue may exist