P0888 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0888 can be explicated as TCM Power Relay Sense Circuit. This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another.

The brighter you are, the more you have to learn! That’s why we are here to provide you more knowledge about the P0888 trouble code. In transmissions with electronic shift controls, power is supplied to the transmission control module through the transmission control output circuit. This circuit would provide the requisite power for the transmission control module, the transmission solenoid/pressure switch assembly, and the PCM under normal functioning conditions.

What causes this problem with the TCM Power Relay Sense Circuit?

• The transmission control relay might be flawed
• Issues related to an open TCR output circuit
• A short in the TCR control or output circuit
• There can be inoperative powertrain control module
• Imperfect connection within the circuit
• The transmission solenoid/pressure switch assembly might not be functioning properly

1. Engine Control Module - OBD Code P0888 can appear because of faulty Engine Control Module.
2. Body Control Module Component - There can be some issues with the Body Control Module Component due to which you may see P0888 code appearing over and over again. Visit us to buy best quality Body Control Module Component online.
3. Electronic Control Unit - Are you facing some faults in your Electronic Control Unit? Don’t worry and get them replaced or else P0888 code can turn up.
4. Auto Transmission Control Module - Common cause behind this P0888 error code can be some fault in Auto Transmission Control Module. So, it will be a good decision to replace them now.
5. Powertrain Control Module - Electronic Control Unit is perfectly fine but still but having that trouble code P0888 flashing? In such a situation your Powertrain Control Module might be faulty. Why don’t you think of getting that replaced?

It is essential to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P0888 here:

Common Symptoms

• The fuel consumption might start increasing
• Transmission not skidding properly

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0888:

• It is essential to restore the open circuit in the transmission control module
• Repair or replace the quirky input and output sensors
• Rehabilitate the defaults in the TCR harness
• You must fix the defective wiring and connectors
• Make sure to mend the faulty TCR
• The malfunctioning transmission solenoid/pressure switch assembly should be repaired or replaced as per the need 

Parts Avatar Canada is here to solve all your issues related to car parts. We have stocked a wide range of best priced CT Transmission, 700R4 Transmission, ZDF Transmission, 4L60E Transmission, Transmission Rebuild and a lot more to help you out in fixing your car.

If you want to easily diagnose this trouble code, then you must follow the steps which are mentioned here as below:

• A communication bus is represented by CAN which would allow a lot of microcontrollers to communicate with one another without the requirement for a host computer.
• It is a message-based agreement originally designed for vehicle utilization.
• It is a compound conglomeration of wiring harnesses and connectors used as a pipeline of information shared between two or more vehicle control modules.
• Virtually every electrical function is controlled by these controllers of the vehicle, and the powertrain control module is the chief controller.
• Input data from a number of sensors is received by the control modules and emit output signals to system constituents and other control modules.
• We can understand this better with the help of an example. An input signal is received by the PCM from the vehicle speed sensor.
• This signal is orderly moved forward to the affected control modules that utilize the data to accomplish a lot of other tasks.
• The code should then be cleared up and the vehicle should be operated to check if it is returning back again or not.
• This would prove to be very helpful to decide whether or not the failure is intermittent.
• Then the vehicle should be taken out for a test drive to check if the code is returning back again or not.

Common Mistakes When Diagnosing the P0888 Code

• Non-performance of the transmission control module relay
• Failure in the wiring
• Transmission control module might start failing