P0876 OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P0876 can be elucidated as Transmission Fluid Pressure Sensor/Switch "D" Circuit Range/Performance. A voltage signal is received by the PCM/TCM to decide the transmission operating pressure or when a shift is happening. This error code would start triggering up when the "D" input would not match usual operating voltages stored in the memory of the PCM/TCM's. This can also be because of inner mechanical problems which are inside the transmission. You can always refer to the vehicle specific repair manual to decide which is the "D" circuit for your specific automobile.

Want to learn something more about the P0876 fault code? This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

What causes this problem with the Transmission Fluid Pressure Sensor/Switch "D" Circuit Range/Performance?

• Issues of open in the signal circuit to the TFPS sensor
• There can be short to voltage in the signal circuit to the TFPS sensor
• Some issues related to the short to ground in the signal circuit to the TFPS sensor
• There can be inoperative TFPS Sensor
• Inner mechanical transmission problems
• Quirks in the PCM

1. Powertrain Control Module - Defective car Powertrain Control Module can be a major reason why P0876 code depicts. So, make sure to replace it online so that you don’t have to face any further issues.
2. Oil Pressure Sender - Everything is okay with the Powertrain Control Module and still OBD code P0876 triggering? Then there must be some defects in Oil Pressure Sender. Replace them as soon as possible.
3. Auto Transmission Shift Solenoid - P0876 code flashing? Get your Auto Transmission Shift Solenoid inspected from a mechanic.
4. Electronic Control Unit - If everything is alright with PCM, then there is surely some defect in Electronic Control Unit. Get it replaced before the situation gets worse.
5. Body Control Module Component - P0876 code can display due to some issues in the Body Control Module Component. So, it is very important to replace the Body Control Module Component with us at equitable prices.
6. Fuel Pressure Sensor - Do you remember when was the last time you got your car Fuel Pressure Sensor checked up? A dirty Fuel Pressure Sensor can cause a lot of issues like displaying P0876 code.
7. Auto Transmission Valve Body Kit - Poor Auto Transmission Valve Body Kit can cause a lot of difficulties, so why not get it replaced at time?
8. Auto Transmission Control Module - Are there some faults in your Auto Transmission Control Module? Don’t waste time and get them replaced or else P0876 code can turn up.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Illumination in the service engine soon light
• The shift quality might start changing
• Automobile starts off in 2nd or 3rd gear

The repairs which you will have to do to correct this fault code are simply straightforward; you can surely pinpoint the necessary repairs on the basis of your diagnosis. Have a look at some common fixes:

• You must fix the defective torque converter and can always install a new one
• Make sure to mend the faulty transmission
• It is essential to fix the leakages
• Repair or replace the quirky wiring or connectors
• Rehabilitate the defaults in the hydraulic pressure pump
• The malfunctioning transmission fluid pressure sensor should be repaired or replaced as per the need
• Carefully adjust the faults in the PCM

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of 700r4 Transmission, Zf Transmission, 4l60e Transmission, Proportioning Valve, Oil Pressure Switch, Bleeder Valve, Pcm Car and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• A suitable OBD-II scanner (or code reader) and a digital volt/ohmmeter will be most helpful in performing a successful diagnosis. Use the vehicle information source to search for applicable technical service bulletins (TSB).
• You can start the process of diagnosis with the power associated trouble code or with a number of code diagnosis. This might be the reason why P0876 error code is appearing.
• After that the transmission fluid pressure sensor/switch should be situated on your specific automobile. The TFPS is generally found attached to the side of the valve body inside the transmission. It can also be situated on the side of the transmission case.
• Now once it has been located, then the connector as well as wiring should be visually located. You can always search for the wires which are bare, burned spots as well as plastic which has been melted. The connector should be pulled apart and the terminals which are inside the connector should be inspected properly.
• You must check if they are appearing burnt and if there is a green tint, then it would indicate that there is corrosion. This can happen if they are attached outside the case of the transmission.
• An electrical contact cleaner as well as plastic bristle brush should be used to clean the terminals as per the requirement.
• It should be allowed to dry properly and then electrical grease should be applied at the places where the terminals are in contact.
• By using a scan tool, all the diagnostic trouble codes should be cleared up from the memory. Then check if the P0876 code has returned or not.
• If you find out that it is not appearing again, then it would mean that there were some defects in the connections.
• Now if this error code returns, then you should definitely test the TFPS sensor as well as the related circuits.
• The electrical connector at the TFPS sensor should be disconnected with the key off. A digital voltmeter should be connected to the ground or low reference terminal at the TFPS sensor wiring harness connector.
• Then a read lead should be connected to the digital voltmeter. Then the key should be turned on and then engine should be off.
• You should carefully check the manufacturer's specifications. The reading of the voltmeter should be either 12 volts or 5 volts.
• You can always wiggle the connections to check if they are changing or not. Now if the voltage is not correct, then the ground wire should be repaired properly. Make sure to restore the PCM/TCM.
• Then one lead of an ohmmeter should be connected to the signal terminal at the TFPS sensor. Then the other lead should be connected to the ground at the sensor.
• You can always inspect the manufacturers specifications on the resistance of the sensor so that the resistance can be properly tested when no pressure has been applied to it. The resistance should be monitored and the connector at the transmission fluid pressure sensor/switch should be wiggled.
• Now if all the tests have been passed and still the P0876 error code is appearing, then there is some issue with the TFPS sensor or there can be some failures in the internal transmission as well.
• So, make sure that you replace the TFPS sensor. If you are not sure about it, then you can always take help from the technician. The PCM/TCM should be programmed properly and at the same time should be calibrated. This is done to install it in a right way.

Common Mistakes When Diagnosing The P0876 Code

• A big mistake which is made by a lot of technicians is that they assume that this fault code is appearing because of leakage in the transmission, when in reality the actual reason is the low fluid condition which results in damaging the transmission constituents.
• One another common mistake which is made by the mechanics is that they might simply replace the transmission without any need.