P0825 - OBD Trouble Code

<<See All OBD Codes

The trouble code P0825 can be elucidated as Gear Lever Push-Pull Switch (Shift Anticipate). It is a generic powertrain code which is associated with the transmission including pressure defects and failures in the sensor. Now in this situation, a defect in the electrical circuit of the gear lever push-pull switch to transmission range correlation circuit has been found by the engine control module.

Want to learn something more about the P0825 fault code? This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

What causes this problem with the Gear Lever Push-Pull Switch (Shift Anticipate)?

• Some issues related to the liquids spilled onto the gear lever push-pull switch inside the passenger compartment
• Malfunctioning gear lever push-pull switch
• Unusable gear lever push-pull switch
• The electrical wiring and connectors to the gear lever push-pull switch might not be functioning properly

1. Auto Transmission Control Module - Defective car Auto Transmission Control Module can be a major reason why P0825 code depicts. So, make sure to replace it online so that you don’t have to face any further issues.
2. Powertrain Control Module - Everything is okay with the Auto Transmission Control Module and still OBD code P0825 triggering? Then there must be some defects in Powertrain Control Module. Replace them as soon as possible.
3. Auto Transmission Shift Solenoid - P0825 code flashing? Get your Auto Transmission Shift Solenoid inspected from a mechanic.
4. Body Control Module Component - If everything is alright with PCM, then there is surely some defect in Body Control Module Component. Get it replaced before the situation gets worse.
5. Automatic Transmission Sensor - P0825 code can display due to some issues in the Automatic Transmission Sensor. So, it is very important to replace the Automatic Transmission Sensor with us at equitable prices.
6. Engine Control Module - Do you remember when was the last time you got your car Engine Control Module checked up? A dirty Engine Control Module can cause a lot of issues like displaying P0825 code.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• Check engine light might come into signal
• The manual shift option may be deactivated
• The automobile might not have any other symptoms
• Overdrive light may appear
• Diminishing fuel efficiency
• Vehicle may shift forcefully
• Transmission might go into “limp” mode

The repairs which you will have to do to correct this fault code are simply straightforward; you can surely pinpoint the necessary repairs on the basis of your diagnosis. Have a look at some common fixes:

• Make sure to clean the shifter area if it has spilled liquids
• You must fix the defective electrical wiring, harnesses, or connectors
• It is essential to restore the flawed gear lever push-pull shift switch
• All the codes should be cleared up and the vehicle should be taken out for a test drive 

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Auto Trans Shift Lever, Hurst Shifter, B&M Ratchet Shifter, B&M Ratchet Shifter, Gear Lever Position Sensor and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• The first and foremost thing which you should do while diagnosing a P0825 fault code is to use an OBD-II scanner.
• The passenger compartment should be visually inspected that might have got into the up and down shift switch.
• Then the next step is to check the circuits wiring for signs of defects, corrosion, or wear.
• The reference voltage and ground signals at the gear lever push-pull switch and actuators should be inspected properly.
• A digital volt/ohmmeter should be utilized to inspect for continuity and resistance if reference voltage and/or ground signals were open.
• All the associated circuits as well as switches should be tested properly for continuity and resistance.

Common Mistakes When Diagnosing The P0825 Code

• Before inspecting and diagnosing quirky transmission wiring, you have to make sure to inspect whether liquid was spilled on the shifter in the passenger compartment.
• It is very important to cleanse as well as mend any defective wiring or connectors at the shift switch location.
• Then the next step is to reset and retest the system before diagnosing and performing more complex wiring rebuilds.