P080C OBD Error Code: Problem & Solutions

<<See All OBD Codes

The trouble code P080C can be explicated as Upshift/Skip Shift Solenoid Control Circuit Low. This code is a generic trouble code, meaning it applies to all vehicles equipped with the OBD-II system, especially those made from 1996 up to present. It’s also more common among Audi, Citroen, Chevrolet, Ford, Hyundai, Nissan, Peugeot, and Volkswagen vehicles. Specifications on the definition, troubleshooting, and repairs, of course, vary from one make and model, powertrain configuration type, to another.

The brighter you are, the more you have to learn! That’s why we are here to provide you more knowledge about the P080C trouble code. The transmission control module monitors the upshift/skip shift solenoid circuit signal. The P080C error code would be set up by the TCM when the upshift/skip shift solenoid would not be as per the parameters set by the manufacturer.

What causes this problem with the Upshift/Skip Shift Solenoid Control Circuit Low?

• There can be inoperative upshift/skip shift solenoid
• There can be opened or shorted upshift/skip shift solenoid harness
• There can be distorted electrical connection in the upshift/skip shift solenoid circuit

1. Engine Wiring Harness - OBD Code P080C can appear because of faulty Engine Wiring Harness.
2. Body Control Module Component - There can be some issues with the Body Control Module Component due to which you may see P080C code appearing over and over again. Visit us to buy best quality Body Control Module Component online.
3. Auto Transmission Valve Body Kit - Are you facing some faults in your Auto Transmission Valve Body Kit? Don’t worry and get them replaced or else P080C code can turn up.
4. Auto Transmission Shift Solenoid - Common cause behind this P080C error code can be some fault in Auto Transmission Shift Solenoid. So, it will be a good decision to replace them now.
5. Automatic Transmission Filter - PCM is perfectly fine but still but having that trouble code P080C flashing? In such a situation your Automatic Transmission Filter might be faulty. Why don’t you think of getting that replaced?
6. Powertrain Control Module - The P080C code can also arise due to some issues in Powertrain Control Module. So, it is advised to replace them as soon as possible.
7. Transmission Torque Converter - P080C code does not really end up spoiling your Powertrain Control Module, but it might also accompany few Transmission Torque Converter issues. We have best Transmission Torque Converter with us.

It is essential to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P080C here:

Common Symptoms

• Visibility in the check engine light

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P080C:

• You must fix the defective fuse or fuse-able link
• Make sure to mend the faulty ground straps
• It is essential to scrub corrosion from connectors
• Repair or replace the quirky wiring
• Rehabilitate the defaults in the PCM or TCM

Parts Avatar Canada is here to solve all your issues related to car parts. We have stocked a wide range of best priced engine light, transmission filter, battery connectors, transmission oil, valve body, transmission fluid and a lot more to help you out in fixing your car.

If you want to easily diagnose this trouble code, then you must follow the steps which are mentioned here as below:

• First of all, you should research the technical service bulletins for the specific vehicle by year, model and transmission before you start with the troubleshooting process for any malfunction.
• There can be some situations where this can save a lot of your precious time in the long run by pointing you in the correct way.
• This fault code can be diagnosed by utilizing an OBD-II trouble code scanner.
• A scanner should be used by a professional technician to notice the freeze frame data, to assemble details about the code.
• The mechanic can also check to see if there is presence of additional trouble codes. Now if there are a number of codes, then they should be addressed in the same order in which they are appearing on the scanner.
• After that the mechanic should reset the trouble codes, restart the vehicle, and check to see if the code remains detected.
• If it does not, then the code was likely triggered incorrectly, or represents an intermittent condition.