Error Code P07BE: What It Means & What To Do?

<<See All OBD Codes

If you are experiencing problematic transmission control? Does the car stalls and there’s difficulty in starting? Are you facing problem of coming in and going out of the park control? All these are indications towards a problematic transmission park sensor circuit issue, thus causing OBD code P07BE getting stored in the system.

OBD code P07BE refers to Transmission Park Position Sensor/Switch “A”/” B” Correlation

The trouble code P07BE can be described as Transmission Park Position Sensor/Switch “A”/”B” Correlation. This code is a powertrain diagnostic trouble code. It would apply to the OBD-II vehicles which have a transmission park position switch/sensor. They include but at the same time are not restricted to the automobiles from Dodge, Ford, Toyota, Land Rover, VW, Chevrolet, etc. Their steps for repairing would vary as it all depends upon the year, make, model and powertrain configuration. The fault code P07BE is one of several possible codes associated to the Transmission Park Position Sensor/Switch. The transmission park position sensor/switch circuit is monitored by the transmission control module. Now when the transmission park position sensor/switch would be out of the parameters set by the manufacturer, then the TCM would set this error code.

What causes this problem with the Transmission Park Position Sensor/Switch “A”/”B” Correlation?

• Improper Transmission park position sensor/switch function
• Corroded or damaged connector and harness failure
• Damaged or faulty wiring of the circuit and the sensor
• Defective Transmission Control Module (TCM)
• Faulty Powertrain Control Module (PCM)

1. Transmission Park Position Sensor - Faulty sensor will send wrong information the TCM and the PCM and thus affect the gear shifts and performance. Buy new position sensor now!
2. Transmission Park Position Switch - Always check for park position switch failure and replace as required. Buy new switch and replace the faulty one.
3. Transmission Park Position Sensor/Switch Harness - Damaged harness will affect he engine performance and cause transmission control failure too. Buy new sensor harness today!
4. Transmission Park Position Sensor Connector - Check if the sensor connector is faulty and replace as required. Buy new sensor connector now!
5. Powertrain Control Module - P07BE code can also display due to some defects in the PCM. So, it is very important to replace the powertrain control module components to get the correct readings. Buy new components form us now!
6. Diagnostic Tool - Choose from our wide variety of diagnostic tools to detect and correct the OBD code error.

It is vital to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P07BE here:

Common Symptoms

• Unpredictable gear shifting
• Affected gear shift patterns
• Improper handling and engine stalling
• Automatic Transmission Fluid might start discharging
• Affected throttle response and acceleration

The repairs which you will have to do to correct this fault code are simply straightforward; you can surely pinpoint the necessary repairs on the basis of your diagnosis. Have a look at some common fixes:

• Automatic transmission fluid refill
• Powertrain control module (PCM) and Transmission Control Module (TCM) repair or replace
• Defective electronic control unit replacement
• Automatic transmission filter replacement

Parts Avatar Canada is here to solve all your issues related to car parts. We have stocked a wide range of best priced carburettor, thermocouple, vacuum pump, thermistor, temperature sensor, cv joint, motion sensor, map sensor and a lot more to help you out in fixing your car.

Have a look at some steps which you should follow in order to diagnose this fault code:

• Use the OBD scanner and retrieve all the coded and freeze frame the data. Then do the test run the vehicle again under same circumstances to see if the code returns to make sure which codes are persistent.
• Start with a visual inspection of all wiring and connectors. Repair or replace damaged, disconnected, shorted, or corroded wiring, connectors, and components as required.
• There would a need of a digital multimeter and the specific technical references to carry out this procedure. Voltage requirements will vary depending upon the specific year, make and model of the vehicle.
• The requirements of the voltage would differ depending upon the specific vehicle, the transmission park position sensor/switch circuit configuration and the components incorporated.
• Right voltage input to a sensor/switch with no voltage output generally indicates internal failure. If the absence of a power source or ground is identified, continuity testing may be needed to check the overall condition of the wiring and connectors. Resistance or no continuity indicates defective wiring or connectors that are shorted or open. Make sure that you repair them properly or get the replaced.

Common Mistakes When Diagnosing The P07BE Code

• PCM and TCM failure that require repair or replacement
• Transmission Control Park Position Sensor failure
• Transmission Control Park Position Sensor/Switch Harness