Guide To P0767 OBD Error Code Solutions

<<See All OBD Codes

The error code P0767 can be defined as Shift Solenoid D Stuck On.

If a P0767 trouble code has been recorded by the powertrain control module in your car, then it would mean that the shift solenoid D is malfunctioning. If you want that the automatic transmission of your vehicle should work efficiently, in that case the fluid should easily move in the hydraulic circuits, and at the same time it should facilitate some change in the ratios of the gear. Then it would be able to shift up and down.

Are you willing to learn something more about this fault code?

If the gear ratio would not be as per the parameters set by the manufacturer, then it would give an illumination to the check engine light. This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

What causes this problem with the Shift Solenoid D Stuck On?

• Smashed connector
• Quirky powertrain control module
• Dirty or clogged transmission filter
• Malfunctioning transmission valve body
• Confined hydraulic passages
• Defective wiring
• The fluid level might be inadequate
• Issue of dirty or contaminated fluid
• Internal damage in the transmission
• Unusable shift solenoid

1. Engine Wiring Connectors - A faulty Engine Wiring Connectors can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Auto Transmission Shift Solenoid - If everything is alright with PCM, then there is surely some defect in Auto Transmission Shift Solenoid. Get it replaced before the situation gets worse.
3. Body Control Module Component - P0767 code can display due to some issues in the Body Control Module Component. So, it is very important to replace the Body Control Module Component with us at equitable prices.
4. Electronic Control Unit - Do you remember when was the last time you got your car Electronic Control Unit checked up? A dirty Electronic Control Unit can cause a lot of issues like displaying P0767 code.
5. Engine Wiring Harness - Poor Engine Wiring Harness can cause a lot of difficulties, so why not get it replaced at time?
6. Automatic Transmission Sensor - Are there some faults in your Automatic Transmission Sensor? Don’t waste time and get them replaced or else P0767 code can turn up.
7. Powertrain Control Module - OBD Code P0767 can appear because of faulty Powertrain Control Module.

There could be countless symptoms which that would accompany with this fault code. Willing to know some common symptoms of OBD Trouble Code P0767? Your wish is our demand. Have a look at them below:

Common Symptoms

• Transmission skidding
• Overheating of the transmission
• Flashing up of the check engine light
• Issue of transmission catches in gear
• Overall fuel economy can start declining
• There can be engine misfires
• Vehicle might start entering the limp mode

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Correct the insufficient fluid level
• The faulty powertrain control module should be repaired or replaced
• Repair or replace the defective transmission valve body
• If you find out that the transmission filter is dirty or clogged, then it should be repaired or replaced
• Correct the malfunctioning shift solenoid
• Make sure that you repair the defective wiring
• Inspect the internal failure in the transmission

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of engine light, transmission filter, transmission valve body, torque converter, battery connectors, engine light, transmission oil, valve body, transmission fluid, transmission sensor and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0767 code to be stored:

Check for technical service bulletins which pertain to the vehicle, symptoms, and codes prior to beginning the troubleshooting process for any malfunction. In some circumstances this can save a lot of time in the long run by pointing you in the right direction. You can always check the vehicle records to verify the last time that the filter and fluid was changed if possible.

Fluid & Wiring Inspections

• The first step is to make sure the fluid level is correct and inspect the condition of the fluid for contamination.
• After that perform visual inspection to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots should be performed.
• Next is to check the connectors and connections for security, corrosion and damaged pins. This process must include all wiring and connectors to the transmission solenoids, transmission pump and the PCM.
• It depends upon the configuration; the transmission linkage should be inspected for security and binding issues.

Advanced Steps

• The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately.
• These procedures require a digital multimeter and the specific technical references for the vehicle.
• Voltage requirements will vary based of the specific year and model of the vehicle.
• You should follow the specific troubleshooting chart for your vehicle.

Continuity Checks

• Continuity checks should always be performed with the power removed from the circuit and the normal readings for wiring and connections should be 0 ohms of resistance unless otherwise specified by the technical data.
• Resistance or no continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.

Common Mistakes When Diagnosing The P0767 Code

• Defaults in the transmission shift solenoid
• Wiring related issues
• There can be a failure in the transmission control module
• Diminishing transmission fluid level