P0734 - OBD Trouble Code

<<See All OBD Codes

Are you experiencing hard gear shifts and gear slipping in fourth gear? Is there a lack of engine power and hesitation during acceleration? Is the Check Engine Light illuminating on dashboard? All these may be due to heat up problems with the engine cylinder flashing and storing OBD code P0734 in the Powertrain Control Module (PCM).

When the OBD Code P0734 is set in the Powertrain Control Module, it means that the PCM is seeing a greater than specified RPM difference between the rotational speed of the Input RPM Sensor and the Transmission Output RPM Sensor when the vehicle is in 4th gear. This can occur during shifting or when driving at steady speeds. It often implies that the transmission is slipping.

Thus, this code indicates that an abnormality has been detected in the gear ration of one of the automatic transmissions gears, causing the storage of a code in the Powertrain Control Module (PCM) and illumination of the Check Engine Light.

What causes this problem with the Gear 4 Incorrect ratio?

• Faulty 4th gear related shift solenoid
• Faulty 4th gear related gear set or clutch pack
• Engine Coolant Temperature Sensor faulty
• Defective Valve Body
• Dirty transmission fluid that restricts the hydraulic passages

1. Automatic Transmission Solenoid - Check for faulty shift solenoid for the fourth gear and replace it, if defective. Buy new solenoid from us.
2. Transmission Control Module - If the transmission control module goes bad, it will be impossible for the transmission system to take any decisions and thus needs to be replaced immediately.
3. Automatic Transmission Sensor - If the transmission sensor has gone out, then there will be a problem with the engine speed and the gear transitions. Thus, replace faulty sensors at first go. Buy new sensor now!
4. Auto Transmission Torque Converter - It is important to check for faulty transmission torque converter and need to replace it immediately. Buy new torque converter now!
5. Automatic Transmission Connector - Inspect for faulty connectors to the TCM and the PCM and replace them immediately and they can be the main reason for this kind of problem. Buy new connectors now!
6. Engine Control Module - Faulty ECMs may lead to engine stalling or not starting, and check engine lights being on. Replace faulty ECM components with us.
7. Powertrain Control Module - P0734 error can also relate to fault in the PCM and other electrical components. Buy all the Powertrain related parts with us.
8. Diagnostic Tool - Visit us today to grab amazing deals on quality diagnostic tools to detect and correct the OBD error codes.

Our main motive is to achieve customer satisfaction and that’s why we will help you to diagnose P0734 code by mentioning some major symptoms below:

Common Symptoms

• Check Engine Light will illuminate
• Vehicle will not shift properly
• Decrease in fuel economy
• Transmission Slipping

Have a look at some ways with which you can correct the P0734 code:

• If the transmission has suffered damage due to a low fluid condition, first rebuild the transmission, perform a fluid flush, and replace the torque converter
• Check the wiring or connectors and replace any damaged, or faulty, wiring or connectors
• Repair any leaks if the transmission fluid looks like it is in good condition and is only low
• Replace the hydraulic pump if this component is damaged
• Repair or replace any damaged circuits or connectors
• Replace the shift solenoid, or solenoid pack if faulty
• Replace the PCM, if found faulty

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Shift Solenoid, Powertrain Control Module, Transmission Control Module, Turbo, Oil Pressure Sensor and many more. Now all your problems would vanish within no time.

Here are some steps which you should follow in order to diagnose this fault code:

• Visually inspect all wiring, connectors, and components associated with the transmission system. They should look for any loose, damaged, or corroded wiring, components, or connectors, replacing them if needed.
• Save the freeze frame data and any stored trouble codes on the PCM using the scanner. Clear any codes and test drive the vehicle to see if the codes return. If the code returns, check the individual auto transmission connector to see if a reference voltage or ground signal are present.
• Check the transmission fluid level and condition and lookout for a burnt or abnormal smell, which can indicate that the transmission has suffered damage from a low fluid condition. If this is the case, the mechanic should remove the transmission pan and inspect it for pieces of the clutch or other debris.
• If the transmission fluid is low, fill the transmission fluid to a point that any leaks can be detected and repaired. Once all leaks are found and fixed, the transmission fluid must be filled to an appropriate level.
• Clear the code, allow the vehicle to reach a normal operating temperature, and test drive the vehicle to see if the trouble code returns.
• If the transmission is still slipping or hesitating, the mechanic should connect a manual pressure gauge and should check the pressure of the transmission hydraulic pump. Compare the mechanic findings to that of the manufacturer specifications.
• Use the digital volt/ohmmeter to test for reference voltage and ground signal at the shift solenoid. Check for circuit continuity, making sure to disconnect any related control modules to prevent memory loss.
• Test all related circuits for resistance and continuity, comparing their findings to the manufacturer's specifications. If everything checks out and is in good condition, diagnose the PCM for failure and repair or replace as required.
• Once all repairs are made, clear the code and retest the system to see if the trouble code returns.

Common Mistakes When Diagnosing the P0734 Code

Some of the common mistakes done while changing diagnosing the OBD code P0734 are:

• Engine Misfire problem
• Internal Transmission problem
• Driveline problem