P0651 OBD Error Code: Problem & Solutions

<<See All OBD Codes

This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

P0651 fault code can be defined as Sensor Reference Voltage B Circuit Open.

The P0651 trouble code would indicate that the sensor reference voltage B circuit is open. It means that there is some default in the sensor reference voltage "B". The voltage can be higher or sometimes even lower than the expectations.

What causes this problem with the Sensor Reference Voltage B Circuit Open?

• Bad quality electrical connection in the ECM circuit
• There can be some defects in the engine control module
• The ECM harness might be opened or shorted
• Issue of shortened sensor on a 5-volt circuit

1. Fuel Injection Harness/Wiring - A faulty Fuel Injection Harness/Wiring can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Fuel Injector - If everything is alright with PCM, then there is surely some defect in Fuel Injector. Get it replaced before the situation gets worse.
3. Powertrain Control Module - P0651 code can display due to some issues in the Powertrain Control Module. So, it is very important to replace the Powertrain Control Module with us at equitable prices.
4. Throttle Body - Do you remember when was the last time you got your Car Throttle Body checked up? A dirty Throttle Body can cause a lot of issues like displaying P0651 code.
5. Engine Control Module - Are there some faults in your Engine Control Module? Don’t waste time and get them replaced or else P0651 code can turn up.

There could be countless symptoms which that would accompany with this fault code. Willing to know some common symptoms of OBD Trouble Code P0651? Your wish is our demand. Have a look at them below:

Common Symptoms

• There might be a hard or no start condition
• Car engine running roughly
• Decrease in the fuel efficiency
• Car engine can start misfiring
• Check engine light may not turn on when a problem is present
• Check engine light may be on when no problems are present

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• First of all, the mechanic should check the code with an OBD-II scanner
• After that it is essential to reset the codes, after which the mechanic will take the vehicle for a road test. There can be a lot of cases where the code might not come back
• Carefully inspect the connectors, circuits, and wiring and you can always replace them as per the need
• Make sure to check the engine control module and all components on that circuit

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of Body Control Module, Injection Pump, Fuel Injection Kit, Fuel Injector Tester, Diesel Fuel Injectors, Diesel Injector Tester and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0651 code to be stored:

If you want to diagnose the issue in your vehicle as well as access data regarding the fault and necessary repair, then you will require an OBD-II scanner

After that the data should be examined properly to determine when the code was set

The next step would be to reset the codes and then the vehicle should be taken out for a test drive

There are a lot of cases where the mechanic would be able to determine the issue depending upon the data, they receive

Common Mistakes When Diagnosing The P0651 Code

• Most of the times when the P0651 trouble code is being diagnosed, people make mistake of spending a lot of precious time searching for symptoms and stored codes which are present in the vehicle and they may not have anything to do with this error code.
• The car mechanic might rush the testing process due to which the results would be inaccurate and he would misdiagnose the actual issue. This would result in a lot of wastage of time as well as money.